SMD code A2s
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
The last letter, s, is lower case, which on NXP and Philips parts is a date or factory code, so it was set aside and A2 was searched.
273 parts are printed A2s
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
MBT3906DWSOT-3636 pins, onsemiNot recordedSOT-3636 pinsonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-363
- Pins
- 6
- Details
- Si-pnp: Dual, AF, 40V, 200mA, 150mW, B=60..300, >250MHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
MBT3906DW1SOT-3636 pins, onsemiNot recordedSOT-3636 pinsonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-363
- Pins
- 6
- Details
- dual 2N3906
- Source
- Published code list
Is it dead? The meter test is below: This part.
MBT3906DW1T1SOT-3636 pins, onsemiNot recordedSOT-3636 pinsonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-363
- Pins
- 6
- Source
- Published code list
Is it dead? The meter test is below: This part.
MC2833SOT-233 pins, IshNot recordedSOT-233 pinsIsh
- What it is
- Not recorded
- Maker
- Ish
- Package
- SOT-23
- Pins
- 3
- Details
- Si-diode: Sw, Hi-sp, 50V, 100mA, Vf<1.2V(100mA), 2.8pF, <4ns
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
MC2843SOT-3233 pins, IshNot recordedSOT-3233 pinsIsh
- What it is
- Not recorded
- Maker
- Ish
- Package
- SOT-323
- Pins
- 3
- Details
- Si-diode: Sw, Hi-sp, 50V, 100mA, Vf<1.2V(100mA), 2.8pF, <4ns
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
MIC803-40D2VC3SOT-323Voltage supervisor, 3 pins, MicrelVoltage supervisorSOT-3233 pinsMicrel
- What it is
- Voltage supervisor
- Maker
- Micrel
- Package
- SOT-323
- Pins
- 3
- Details
- Microprocessor reset circuit
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
MIC803-40D2VM3SOT-233 pins, MicrelNot recordedSOT-233 pinsMicrel
- What it is
- Not recorded
- Maker
- Micrel
- Package
- SOT-23
- Pins
- 3
- Details
- Microprocessor reset circuit
- Source
- Published code list
Is it dead? The meter test is below: This part.
MM3Z5241BSOD-323Zener diode, 2 pins, BytesonicZener diodeSOD-3232 pinsBytesonic
- What it is
- Zener diode
- Maker
- Bytesonic
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 11V±5%, Izt=20mA, Zzt=22, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MM3Z5241BHSOD-323Zener diode, 2 pins, Zowie TechnologyZener diodeSOD-3232 pinsZowie Technology
- What it is
- Zener diode
- Maker
- Zowie Technology
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 10.45..11.55V, Izt=20mA, Zzt=22, 300mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MMBD2836SOT-233 pins, onsemiNot recordedSOT-233 pinsonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- dual ca sw diode 75V
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
MMBD2836LT1SOT-236 pins, onsemiNot recordedSOT-236 pinsonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 6
- Source
- Published code list
Is it dead? The meter test is below: This part.
MMSZ11TSOD-123Zener diode, 2 pins, MotorolaZener diodeSOD-1232 pinsMotorola
- What it is
- Zener diode
- Maker
- Motorola
- Package
- SOD-123
- Pins
- 2
- Details
- Zener diode: 11V±5%, Izt=5mA, Zzt=20, 500mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
N6200M5G-1.5SOT-23-5DC-DC converter, 5 pinsDC-DC converterSOT-23-55 pinsNot recorded
- What it is
- DC-DC converter
- Maker
- Not recorded
- Package
- SOT-23-5
- Pins
- 5
- Details
- Down converter
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NLAS4501DFSOT-3535 pins, onsemiNot recordedSOT-3535 pinsonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-353
- Pins
- 5
- Details
- CMOS logic IC: Single-pole single-throw analog switch
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
1 more part has no package on record
MSCD102ZowieNot recordedNot recordedNot recordedZowie
- What it is
- Not recorded
- Maker
- Zowie
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Si-diode: Schottky Barrier Rectifier, 20V, 1A, Vf<0,45V(1A)
- Source
- Published code list
Is it dead? The meter test is below: Schottky diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.