Skip to content

SMD code A82 in SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

3 parts in SOT-23 are printed A82

Not sure which one you have?

Answer up to 4 quick questions and these 7 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BAS21SOT-23Switching diode, 3 pins, Taitron ComponentsSwitching diode3 pinsTaitron Components
    What it is
    Switching diode
    Maker
    Taitron Components
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • BAS21-AUSOT-23Switching diode, 3 pins, PanjitSwitching diode3 pinsPanjit
    What it is
    Switching diode
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • CMPD2003SOT-23Schottky diode, 3 pins, Central SemiconductorSchottky diode3 pinsCentral Semiconductor
    What it is
    Schottky diode
    Maker
    Central Semiconductor
    Package
    SOT-23
    Pins
    3
    Details
    Diode: Schottky, Sw, 200V, 200mA, Vf=1.25V(200mA), <5pF
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 4 more parts have no package on record. Nothing rules them out, so they stay.
    • BAS21WSSwitching diode, Taitron ComponentsSwitching diodeNot recordedTaitron Components
      What it is
      Switching diode
      Maker
      Taitron Components
      Package
      Not recorded
      Pins
      Not recorded
      Details
      SMD Switching Diodes (Three Terminals)
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Silicon diode.

    • TWD21WSSwitching diode, Taitron ComponentsSwitching diodeNot recordedTaitron Components
      What it is
      Switching diode
      Maker
      Taitron Components
      Package
      Not recorded
      Pins
      Not recorded
      Details
      SMD Switching Diodes (Two Terminals)
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Silicon diode.

    • DAM1MA82ESD protection diode, HitachiESD protection diodeNot recordedHitachi
      What it is
      ESD protection diode
      Maker
      Hitachi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      ElectroStatic Discharge Protection diode: Vdc=59V, Vzt=73.8..90.2V, Izt=3mA, 600W(100µs)
      Source
      Published code list

      Is it dead? The meter test is below: TVS or ESD protection diode.

    • DAM3MA82ESD protection diode, HitachiESD protection diodeNot recordedHitachi
      What it is
      ESD protection diode
      Maker
      Hitachi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      ElectroStatic Discharge Protection diode: Vdc=59V, Vzt=73.8..90.2V, Izt=10mA, 1800W(100µs)
      Source
      Published code list

      Is it dead? The meter test is below: TVS or ESD protection diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as A82

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.