Skip to content
WhatSMDSign in

SMD code ADS in DFN

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

2 parts in DFN are printed ADS

Not sure which one you have?

Answer up to 4 quick questions and these 7 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • MAX6469TA33AD3DFNMaxim Integrated ProductsNot recordedNot recordedMaxim Integrated Products
    What it is
    Not recorded
    Maker
    Maxim Integrated Products
    Package
    DFN
    Pins
    Not recorded
    Details
    Linear voltage regulator with volatge detector: LDO, 3.3V±1.3%, 300mA, -Reset PPO, Set, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • TC1302ADSVMFDFNLDO regulator, MicrochipLDO regulatorNot recordedMicrochip
    What it is
    LDO regulator
    Maker
    Microchip
    Package
    DFN
    Pins
    Not recorded
    Details
    Linear voltage regulator IC: LDO, Dual out, Vo1/Vo2=3.0V(300mA)/1.5V(150mA)±2.5%, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • 5 more parts have no package on record. Nothing rules them out, so they stay.
    • 2SA1418-SSanyo ElectricNot recordedNot recordedSanyo Electric
      What it is
      Not recorded
      Maker
      Sanyo Electric
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Si-pnp: HV, Pre-Drv, 180V, 700mA, 500mW, B=140..280, 120MHz
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • MAX6405BS434 pins, Analog DevicesNot recorded4 pinsAnalog Devices
      What it is
      Not recorded
      Maker
      Analog Devices
      Package
      Not recorded
      Pins
      4
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • MAX6478BL285AD3Maxim Integrated ProductsNot recordedNot recordedMaxim Integrated Products
      What it is
      Not recorded
      Maker
      Maxim Integrated Products
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Linear voltage regulator with volatge detector: LDO, 2.85V±1.3%, 300mA, -Reset ODO, Set, +CE
      Source
      Published code list

      Is it dead? The meter test is below: Voltage regulator.

    • MAX13044BC12 pins, Analog DevicesNot recorded12 pinsAnalog Devices
      What it is
      Not recorded
      Maker
      Analog Devices
      Package
      Not recorded
      Pins
      12
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • XC6241A401NR-GLDO regulator, TorexLDO regulatorNot recordedTorex
      What it is
      LDO regulator
      Maker
      Torex
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Linear voltage regulator IC: LDO, 4.0V±1%, 150mA, +CE, CL
      Source
      Published code list

      Is it dead? The meter test is below: Voltage regulator.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as ADS

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with ADS

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.