SMD code AFAA
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
9 parts are printed AFAA
Not sure which one you have?
Answer up to 4 quick questions and these 9 parts are ranked, with a meter test that settles it. It works on a dead part too.
CN809RSOT-23ConsonanceSOT-23Consonance
- What it is
- Voltage supervisor
- Maker
- Consonance
- Package
- SOT-23
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
MAX809S-263SOT-23HXYSOT-23HXY
- What it is
- Voltage supervisor
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
AM809RSOT-23Xiang Shuo ElectronicsSOT-23Xiang Shuo Electronics
- What it is
- Voltage supervisor
- Maker
- Xiang Shuo Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.63V±1.5%, -Reset PPO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
HM809RSOT-23Huamei SemiconductorSOT-23Huamei Semiconductor
- What it is
- Voltage supervisor
- Maker
- Huamei Semiconductor
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.63V±2.5%, -Reset PPO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
HWD809REUSOT-23Chengdu Sino MicroelectronicsSOT-23Chengdu Sino Microelectronics
- What it is
- Voltage supervisor
- Maker
- Chengdu Sino Microelectronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.63V±2%, -Reset PPO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
MAX809RSOT-23Analog DevicesSOT-23Analog Devices
- What it is
- Not recorded
- Maker
- Analog Devices
- Package
- SOT-23
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: This part.
MAX809RURSOT-23Analog DevicesSOT-23Analog Devices
- What it is
- Not recorded
- Maker
- Analog Devices
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 2,63V, -Reset Push-pull output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
MAX809RXRSOT-23Analog DevicesSOT-23Analog Devices
- What it is
- Not recorded
- Maker
- Analog Devices
- Package
- SOT-23
- Pins
- 3
- Details
- microproc -ve reset gen 3.0V
- Source
- Published code list
Is it dead? The meter test is below: This part.
TC1301AFAAVMFDFNMicrochipDFNMicrochip
- What it is
- Not recorded
- Maker
- Microchip
- Package
- DFN
- Pins
- Not recorded
- Details
- Linear voltage regulator with volatge detector: LDO, Dual out, Vo1/Vo2=2.8V(300mA)/3.3V(150mA)±2.5%, Vdet=2.63V±2.5%, +…
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.