Skip to content

SMD code BDP

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 39 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 1.5SMC9.1CASMCTVS diode, 2 pins, Ruilong Yuan ElectronicsTVS diodeSMC2 pinsRuilong Yuan Electronics
    What it is
    TVS diode
    Maker
    Ruilong Yuan Electronics
    Package
    SMC
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • 1.5SMCJ7.5ACSMC2 pins, PanjitNot recordedSMC2 pinsPanjit
    What it is
    Not recorded
    Maker
    Panjit
    Package
    SMC
    Pins
    2
    Details
    TVS: 7.5V, 116.3A, 1500W (1ms), Bidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • 1.5SMCJ7.5CASMCTVS diode, 2 pins, PanjitTVS diodeSMC2 pinsPanjit
    What it is
    TVS diode
    Maker
    Panjit
    Package
    SMC
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=7.5V, Vbr=8.33..9.21V, Ipp=116.3A, 1500W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • 2SA1733K-PSOT-23PNP transistor, 3 pins, ROHMPNP transistorSOT-233 pinsROHM
    What it is
    PNP transistor
    Maker
    ROHM
    Package
    SOT-23
    Pins
    3
    Details
    Si-pnp: Sw, 30V, 30mA, 200mW, B=82..180, >400MHz
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • 2SA1808-PSOT-323RF transistor, 3 pins, ROHMRF transistorSOT-3233 pinsROHM
    What it is
    RF transistor
    Maker
    ROHM
    Package
    SOT-323
    Pins
    3
    Details
    Si-pnp: RF, 30V, 30mA, 200mW, B=82..180, >400MHz
    Source
    Published code list

    Is it dead? The meter test is below: Bipolar transistor.

  • 2SA1821-PSOT-416PNP transistor, 3 pins, ROHMPNP transistorSOT-4163 pinsROHM
    What it is
    PNP transistor
    Maker
    ROHM
    Package
    SOT-416
    Pins
    3
    Details
    PNP transistor: HF, 20V, 30mA, 150mW, >400MHz, B=82..180
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • 2SB1189-PSOT-89PNP transistor, 3 pins, ROHMPNP transistorSOT-893 pinsROHM
    What it is
    PNP transistor
    Maker
    ROHM
    Package
    SOT-89
    Pins
    3
    Details
    Si-pnp: AF, 80V, 800mA, 500mW, B=82..180, >100MHz
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • 15SMBJ7.5CASMBTVS diode, 2 pins, UN SemiconductorTVS diodeSMB2 pinsUN Semiconductor
    What it is
    TVS diode
    Maker
    UN Semiconductor
    Package
    SMB
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=7.5V, Vbr=8.33..9.21V, Ipp=116.3A, 1500W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • BCW61DSOT-23PNP transistor, 3 pins, PhilipsPNP transistorSOT-233 pinsPhilips
    What it is
    PNP transistor
    Maker
    Philips
    Package
    SOT-23
    Pins
    3
    Details
    Bipolar transistor, 45 V, 0.1 A
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • CD214C-T7.5CASMCTVS diode, 2 pins, BournsTVS diodeSMC2 pinsBourns
    What it is
    TVS diode
    Maker
    Bourns
    Package
    SMC
    Pins
    2
    Details
    TVS: 7.5V, 116.3A, 1500W(1ms), Bidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • EC76SMCJ7.5CASMCTVS diode, 2 pins, E-CMOSTVS diodeSMC2 pinsE-CMOS
    What it is
    TVS diode
    Maker
    E-CMOS
    Package
    SMC
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=7.5V, Vbr=8.33..9.58V, 116.3A, 1500W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • S-814A51AMC-BDPT2SOT-23-55 pins, ABLICNot recordedSOT-23-55 pinsABLIC
    What it is
    Not recorded
    Maker
    ABLIC
    Package
    SOT-23-5
    Pins
    5
    Details
    equivalent [5.1V LDO]
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • S-814A51AUC-BDPT2SOT-89-55 pins, ABLICNot recordedSOT-89-55 pinsABLIC
    What it is
    Not recorded
    Maker
    ABLIC
    Package
    SOT-89-5
    Pins
    5
    Details
    equivalent [5.1V LDO]
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • SMAJ12CSMATVS diode, 2 pins, BytesonicTVS diodeSMA2 pinsBytesonic
    What it is
    TVS diode
    Maker
    Bytesonic
    Package
    SMA
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMCG7.5CASMCGTVS diode, 2 pins, VishayTVS diodeSMCG2 pinsVishay
    What it is
    TVS diode
    Maker
    Vishay
    Package
    SMCG
    Pins
    2
    Details
    TVS: 7.5V, 116.3A, 1500W (1ms), Bidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

PNP transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.