SMD code BEQ
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
13 parts are printed BEQ
Not sure which one you have?
Answer up to 4 quick questions and these 13 parts are ranked, with a meter test that settles it. It works on a dead part too.
BRSMBJ12CAQSMBTVS diode, 2 pins, Blue RocketTVS diodeSMB2 pinsBlue Rocket
- What it is
- TVS diode
- Maker
- Blue Rocket
- Package
- SMB
- Pins
- 2
- Details
- TVS diode, unidirectional
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
BRSMF12AQSOD-123FTVS diode, 2 pins, Blue RocketTVS diodeSOD-123F2 pinsBlue Rocket
- What it is
- TVS diode
- Maker
- Blue Rocket
- Package
- SOD-123F
- Pins
- 2
- Details
- TVS diode, unidirectional
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
SMCJ17CSMCTVS diode, 2 pins, DOWOTVS diodeSMC2 pinsDOWO
- What it is
- TVS diode
- Maker
- DOWO
- Package
- SMC
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
1.5SMCJ17CSMCTVS diode, 2 pins, PanjitTVS diodeSMC2 pinsPanjit
- What it is
- TVS diode
- Maker
- Panjit
- Package
- SMC
- Pins
- 2
- Details
- TVS: 17V, 49.2A, 1500W (1ms), Bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
2SB1260-QSOT-89PNP transistor, 3 pins, ROHMPNP transistorSOT-893 pinsROHM
- What it is
- PNP transistor
- Maker
- ROHM
- Package
- SOT-89
- Pins
- 3
- Details
- -80V, -1A, General Purpose PNP Bipolar Transistor
- Source
- Published code list
Is it dead? The meter test is below: PNP transistor.
2SB1260QSOT-893 pins, ROHMNot recordedSOT-893 pinsROHM
- What it is
- Not recorded
- Maker
- ROHM
- Package
- SOT-89
- Pins
- 3
- Details
- equivalent 2SB1241Q
- Source
- Published code list
Is it dead? The meter test is below: This part.
EC76SMCJ17CSMCTVS diode, 2 pins, E-CMOSTVS diodeSMC2 pinsE-CMOS
- What it is
- TVS diode
- Maker
- E-CMOS
- Package
- SMC
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=17V, Vbr=18.9..21.7V, 49.2A, 1500W(1ms), Bidir.
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SM15T30CSMC2 pins, STMicroelectronicsNot recordedSMC2 pinsSTMicroelectronics
- What it is
- Not recorded
- Maker
- STMicroelectronics
- Package
- SMC
- Pins
- 2
- Details
- TVS: 28.5..31.5V, 36A, 1500W (1ms), Bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SMCG17CSMCGTVS diode, 2 pins, VishayTVS diodeSMCG2 pinsVishay
- What it is
- TVS diode
- Maker
- Vishay
- Package
- SMCG
- Pins
- 2
- Details
- TVS: 17V, 49.2A, 1500W (1ms), Bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
TC1302BEQVMFDFNLDO regulator, MicrochipLDO regulatorDFNNot recordedMicrochip
- What it is
- LDO regulator
- Maker
- Microchip
- Package
- DFN
- Pins
- Not recorded
- Details
- Linear voltage regulator IC: LDO, Dual out, Vo1/Vo2=2.9V(300mA)/1.7V(150mA)±2.5%, +CE
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
TFMCJ17CSMC2 pins, RectronNot recordedSMC2 pinsRectron
- What it is
- Not recorded
- Maker
- Rectron
- Package
- SMC
- Pins
- 2
- Details
- TVS: 17V, 49.2A, 1500W (1ms), Bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
TV15C170KBSMC2 pins, ComchipNot recordedSMC2 pinsComchip
- What it is
- Not recorded
- Maker
- Comchip
- Package
- SMC
- Pins
- 2
- Details
- TVS: 17V, 10%, 49.2A, 1500W(1ms), Bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
TV15C170KB-GSMCTVS diode, 2 pins, ComchipTVS diodeSMC2 pinsComchip
- What it is
- TVS diode
- Maker
- Comchip
- Package
- SMC
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=17.0V, Vbr=18.90..23.10V, Ipp=49.18A, 1500W(1ms), Bidir.
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PNP transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as BEQ
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.