SMD code C26
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
32 parts are printed C26
Not sure which one you have?
Answer up to 4 quick questions and these 32 parts are ranked, with a meter test that settles it. It works on a dead part too.
10BJ26CASMBTVS diode, 2 pins, JieJieTVS diodeSMB2 pinsJieJie
- What it is
- TVS diode
- Maker
- JieJie
- Package
- SMB
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
10BJ26CA-AUSMBTVS diode, 2 pins, JieJieTVS diodeSMB2 pinsJieJie
- What it is
- TVS diode
- Maker
- JieJie
- Package
- SMB
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
S-LSC0265SBSMBSchottky diode, 2 pins, LRCSchottky diodeSMB2 pinsLRC
- What it is
- Schottky diode
- Maker
- LRC
- Package
- SMB
- Pins
- 2
- Details
- Schottky diode, VR 650 V, IF 2 A, VF Max 1.8 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
2SA1247-26SOT-233 pins, NEC ElectronicsNot recordedSOT-233 pinsNEC Electronics
- What it is
- Not recorded
- Maker
- NEC Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- Si-pnp: GP, 120V, 50mA, 200mW, B=50..100, 100MHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
10SMBJ26CASMBTVS diode, 2 pins, UN SemiconductorTVS diodeSMB2 pinsUN Semiconductor
- What it is
- TVS diode
- Maker
- UN Semiconductor
- Package
- SMB
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=26.0V, Vbr=28.90..31.90V, Ipp=23.8A, 1000W(1ms), Bidir.
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
88C26-AF5SOT-23-5Voltage supervisor, 5 pins, UnisonicVoltage supervisorSOT-23-55 pinsUnisonic
- What it is
- Voltage supervisor
- Maker
- Unisonic
- Package
- SOT-23-5
- Pins
- 5
- Details
- Voltage detector IC: 2.6V±2%, -Reset PPO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
BV-SMCJ26ASMCTVS diode, 2 pins, Bencent ElectronicsTVS diodeSMC2 pinsBencent Electronics
- What it is
- TVS diode
- Maker
- Bencent Electronics
- Package
- SMC
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=26.0V, Vbr=28.90..31.90V, Ipp=35.63A, 1500W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
CM7P611C-26-TSOT-23Voltage supervisor, 3 pins, Canaan MicroelectronicsVoltage supervisorSOT-233 pinsCanaan Microelectronics
- What it is
- Voltage supervisor
- Maker
- Canaan Microelectronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.6V±2%, -Reset PPO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
KIC77C26TSOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
- What it is
- Voltage supervisor
- Maker
- KEC
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.6V±1%, -Reset ODO, Rdt=100ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
LN61FC2242MSOT-23Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-233 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.2V±2%, +Reset PPO, Rdt=400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
5 more parts have no package on record
74AHCT1G126GVLogic gate, NXPLogic gateNot recordedNot recordedNXP
- What it is
- Logic gate
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Buffer
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AHCT2G126DCNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual bus buffer with 3-state output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AHCT2G126DPNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual bus buffer with 3-state output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AHCT2G126GDNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual bus buffer with 3-state output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
KIC77C26MVoltage supervisor, KECVoltage supervisorNot recordedNot recordedKEC
- What it is
- Voltage supervisor
- Maker
- KEC
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Voltage detector IC: 2.6V±1%, -Reset ODO, Rdt=100ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as C26
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 61 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.