Skip to content

SMD code CY

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • TMMSZ4693SOD-123Zener diode, 2 pins, Galaxy MicroelectronicsZener diodeSOD-1232 pinsGalaxy Microelectronics
    What it is
    Zener diode
    Maker
    Galaxy Microelectronics
    Package
    SOD-123
    Pins
    2
    Details
    7.5V, 500mW, Surface Mount Zener Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • ZD4693SHSOD-123Zener diode, 2 pins, CYStekZener diodeSOD-1232 pinsCYStek
    What it is
    Zener diode
    Maker
    CYStek
    Package
    SOD-123
    Pins
    2
    Details
    7.5 V zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 2SC2881-YSOT-89NPN transistor, 3 pins, YFWNPN transistorSOT-893 pinsYFW
    What it is
    NPN transistor
    Maker
    YFW
    Package
    SOT-89
    Pins
    3
    Details
    120V, 0.8A, General Purpose NPN Bipolar Transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: NPN transistor.

  • 2SA1980U-YSOT-323PNP transistor, 3 pins, AUK SemiconductorPNP transistorSOT-3233 pinsAUK Semiconductor
    What it is
    PNP transistor
    Maker
    AUK Semiconductor
    Package
    SOT-323
    Pins
    3
    Details
    PNP transistor: GP, 50V, 150mA, 200mW, B=120..240, 80MHz
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • 2SC2881YSOT-233 pins, ToshibaNot recordedSOT-233 pinsToshiba
    What it is
    Not recorded
    Maker
    Toshiba
    Package
    SOT-23
    Pins
    3
    Details
    NPN power amp hfe 120-240 comp 2SA1201
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • 2SC4209-YSOT-23NPN transistor, 3 pins, ToshibaNPN transistorSOT-233 pinsToshiba
    What it is
    NPN transistor
    Maker
    Toshiba
    Package
    SOT-23
    Pins
    3
    Details
    NPN transistor: AF-Drv, 80V, 300mA, 200mW, B=120..240, 100MHz
    Source
    Published code list

    Is it dead? The meter test is below: NPN transistor.

  • 2SC4209YSOT-233 pins, ToshibaNot recordedSOT-233 pinsToshiba
    What it is
    Not recorded
    Maker
    Toshiba
    Package
    SOT-23
    Pins
    3
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • 2SC4397SOT-3233 pins, Sanyo ElectricNot recordedSOT-3233 pinsSanyo Electric
    What it is
    Not recorded
    Maker
    Sanyo Electric
    Package
    SOT-323
    Pins
    3
    Details
    Si-npn-Digi: Sw, 50V, 100mA, 250MHz, R1=R2=22k
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • 2SC5087YSOT-1434 pins, ToshibaNot recordedSOT-1434 pinsToshiba
    What it is
    Not recorded
    Maker
    Toshiba
    Package
    SOT-143
    Pins
    4
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • 2SC5343E-YSOT-523NPN transistor, 3 pins, AUK SemiconductorNPN transistorSOT-5233 pinsAUK Semiconductor
    What it is
    NPN transistor
    Maker
    AUK Semiconductor
    Package
    SOT-523
    Pins
    3
    Details
    NPN transistor: GP, 60V, 150mA, 150mW, >80MHz, B=120..240
    Source
    Published code list

    Is it dead? The meter test is below: NPN transistor.

  • 5 more parts have no package on record
    • 2SA1980UF-YPNP transistor, AUK SemiconductorPNP transistorNot recordedNot recordedAUK Semiconductor
      What it is
      PNP transistor
      Maker
      AUK Semiconductor
      Package
      Not recorded
      Pins
      Not recorded
      Details
      PNP transistor: GP, 50V, 150mA, 200mW, B=120..240, 80MHz
      Source
      Published code list

      Is it dead? The meter test is below: PNP transistor.

    • 2SC3396Digital transistor (NPN, resistors built in), Sanyo ElectricDigital transistor (NPN, resistors built in)Not recordedNot recordedSanyo Electric
      What it is
      Digital transistor (NPN, resistors built in)
      Maker
      Sanyo Electric
      Package
      Not recorded
      Pins
      Not recorded
      Details
      NPN transistor: Sw, 50V, 100mA, 200mW, 250MHz, R1/R2=22k/22k
      Source
      Published code list

      Is it dead? The meter test is below: Digital transistor.

    • 2SC5087-YRF transistor, ToshibaRF transistorNot recordedNot recordedToshiba
      What it is
      RF transistor
      Maker
      Toshiba
      Package
      Not recorded
      Pins
      Not recorded
      Details
      NPN transistor: VHF/UHF, LN, 20V, 80mA, 150mW, 7GHz, B=120..240
      Source
      Published code list

      Is it dead? The meter test is below: Bipolar transistor.

    • 2SC5343ENPN transistorNPN transistorNot recordedNot recordedNot recorded
      What it is
      NPN transistor
      Maker
      Not recorded
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Published code list

      Is it dead? The meter test is below: NPN transistor.

    • 2SC5343EF-YAUK SemiconductorNot recordedNot recordedNot recordedAUK Semiconductor
      What it is
      Not recorded
      Maker
      AUK Semiconductor
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Si-npn: GP, 60/50V, 150mA, 150mW, >80MHz, B=120..240
      Source
      Published code list

      Is it dead? The meter test is below: This part.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

NPN transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Red probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

PNP transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.