Skip to content

SMD code D23 in SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

15 parts in SOT-23 are printed D23

Not sure which one you have?

Answer up to 4 quick questions and these 17 parts are ranked, with a meter test that settles it. It works on a dead part too.

all SOT-23, 3 pins. What differs:

  • AZ23C22SOT-23Zener diode, PanjitZener diodePanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Details
    22V, 300mW, Surface Mount Zener Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • AZ23C22-AUSOT-23Zener diode, PanjitZener diodePanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • KIC77D23MSOT-23Voltage supervisor, KECVoltage supervisorKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 2.3 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • KIC77D23TSOT-23Voltage supervisor, KECVoltage supervisorKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 2.3 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • 2SK931-23SOT-23Sanyo ElectricNot recordedSanyo Electric
    What it is
    Not recorded
    Maker
    Sanyo Electric
    Package
    SOT-23
    Pins
    3
    Details
    n-FET: GP, 30V, 50mA, 200mW, Idss=10..17mA, Up<2V
    Source
    Published code list

    Is it dead? The meter test is below: MOSFET.

  • AZ23C22-VSOT-23Zener diode, VishayZener diodeVishay
    What it is
    Zener diode
    Maker
    Vishay
    Package
    SOT-23
    Pins
    3
    Details
    Zener diode: Dual, 20.90..23.10V, Zzt=55, Izt=5mA, 300mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • AZZ23C22SOT-23Diodes IncorporatedNot recordedDiodes Incorporated
    What it is
    Not recorded
    Maker
    Diodes Incorporated
    Package
    SOT-23
    Pins
    3
    Details
    dual ca zener 22V 0.3W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • BZD84C22SOT-23Zener diode, Formosa MicrosemiZener diodeFormosa Microsemi
    What it is
    Zener diode
    Maker
    Formosa Microsemi
    Package
    SOT-23
    Pins
    3
    Source
    An older or alternative marking, from a published code list

    Is it dead? The meter test is below: Zener diode.

  • HE61CC3202MRSOT-23Voltage supervisor, Heermicr SemicconductorVoltage supervisorHeermicr Semicconductor
    What it is
    Voltage supervisor
    Maker
    Heermicr Semicconductor
    Package
    SOT-23
    Pins
    3
    Details
    Voltage detector IC: 3.2V±2%, +Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • HE7032HCMRSOT-23Voltage supervisor, Heermicr SemicconductorVoltage supervisorHeermicr Semicconductor
    What it is
    Voltage supervisor
    Maker
    Heermicr Semicconductor
    Package
    SOT-23
    Pins
    3
    Details
    Voltage detector IC: 3.2V±2%, +Reset PPO, Hst.
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • HE7032MCNRSOT-23Voltage supervisor, Heermicr SemicconductorVoltage supervisorHeermicr Semicconductor
    What it is
    Voltage supervisor
    Maker
    Heermicr Semicconductor
    Package
    SOT-23
    Pins
    3
    Details
    Voltage detector IC: 3.2V±2%, +Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • MEZ03-22-T2SOT-23Zener diode, Matsuki Electronic CompanyZener diodeMatsuki Electronic Company
    What it is
    Zener diode
    Maker
    Matsuki Electronic Company
    Package
    SOT-23
    Pins
    3
    Details
    Zener diode: 20.90..23.10V, Izt=5mA, Zzt=55, 300mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • TZT22AWSOT-23Zener diode, Taitron ComponentsZener diodeTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SOT-23
    Pins
    3
    Details
    SMD Zener Diodes (Three Terminals) - 300mW
    Source
    An older or alternative marking, from a published code list

    Is it dead? The meter test is below: Zener diode.

  • XC61CC3202MSOT-23TorexNot recordedTorex
    What it is
    Not recorded
    Maker
    Torex
    Package
    SOT-23
    Pins
    3
    Details
    CMOS-IC: Voltage Detector 3,2V, Reset Push-pull output
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • XE61CC3245MRSOT-23Voltage supervisor, TorexVoltage supervisorTorex
    What it is
    Voltage supervisor
    Maker
    Torex
    Package
    SOT-23
    Pins
    3
    Details
    Voltage detector IC: 3.2V±2%, -Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as D23

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with D23

For a marking with its end worn or burnt off. Each code has a page of its own.

Codes not listed here are printed on 166 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.