Skip to content

SMD code D4 in SOD-123F

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 44 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BZD27C5V1PSOD-123FZener diode, 2 pins, VishayZener diode2 pinsVishay
    What it is
    Zener diode
    Maker
    Vishay
    Package
    SOD-123F
    Pins
    2
    Details
    5.1 V Zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • MMSZ5229A-FLSOD-123FZener diode, 2 pins, Formosa MicrosemiZener diode2 pinsFormosa Microsemi
    What it is
    Zener diode
    Maker
    Formosa Microsemi
    Package
    SOD-123F
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • MMSZ5229BSOD-123FZener diode, 2 pins, Formosa MicrosemiZener diode2 pinsFormosa Microsemi
    What it is
    Zener diode
    Maker
    Formosa Microsemi
    Package
    SOD-123F
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • SM4004FL-CSOD-123FRectifier, 2 pins, SeCoSRectifier2 pinsSeCoS
    What it is
    Rectifier
    Maker
    SeCoS
    Package
    SOD-123F
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • SM4004FLCR-CSOD-123FRectifier, 2 pins, SeCoSRectifier2 pinsSeCoS
    What it is
    Rectifier
    Maker
    SeCoS
    Package
    SOD-123F
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • SOD4004SOD-123FRectifier, 2 pins, Galaxy MicroelectronicsRectifier2 pinsGalaxy Microelectronics
    What it is
    Rectifier
    Maker
    Galaxy Microelectronics
    Package
    SOD-123F
    Pins
    2
    Details
    1A, 400V, Surface Mount Standard Recovery Rectifiers
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • SOF4004SOD-123FRectifier, 2 pins, Galaxy MicroelectronicsRectifier2 pinsGalaxy Microelectronics
    What it is
    Rectifier
    Maker
    Galaxy Microelectronics
    Package
    SOD-123F
    Pins
    2
    Details
    1A, 400V, Surface Mount Standard Recovery Rectifiers
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • TSOD4004SOD-123FRectifier, 2 pins, Galaxy MicroelectronicsRectifier2 pinsGalaxy Microelectronics
    What it is
    Rectifier
    Maker
    Galaxy Microelectronics
    Package
    SOD-123F
    Pins
    2
    Details
    1A, 400V, Surface Mount Standard Recovery Rectifiers
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • MM1Z5226BSOD-123FZener diode, 2 pins, EIC SemiconductorZener diode2 pinsEIC Semiconductor
    What it is
    Zener diode
    Maker
    EIC Semiconductor
    Package
    SOD-123F
    Pins
    2
    Details
    Zener diode: 3.14..3.47V, Izt=20mA, Zzt=28, 500mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • MMSZ5229B-FSOD-123FZener diode, 2 pins, Taitron ComponentsZener diode2 pinsTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SOD-123F
    Pins
    2
    Details
    Zener diode: 4.09..4.52V, Izt=20mA, 500mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • NZH20CSOD-123FZener diode, 2 pins, PhilipsZener diode2 pinsPhilips
    What it is
    Zener diode
    Maker
    Philips
    Package
    SOD-123F
    Pins
    2
    Details
    Zener diode: 20V±5%, If=250mA, 500mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 4 more parts have no package on record. Nothing rules them out, so they stay.
    • BFU690FRF transistor, 4 pins, NXPRF transistor4 pinsNXP
      What it is
      RF transistor
      Maker
      NXP
      Package
      Not recorded
      Pins
      4
      Details
      NPN wideband silicon RF transistor
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Bipolar transistor.

    • EMD4Digital transistor (resistors built in), ROHMDigital transistor (resistors built in)Not recordedROHM
      What it is
      Digital transistor (resistors built in)
      Maker
      ROHM
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Digital transistor.

    • MMBZ5229BWSZener diode, Taitron ComponentsZener diodeNot recordedTaitron Components
      What it is
      Zener diode
      Maker
      Taitron Components
      Package
      Not recorded
      Pins
      Not recorded
      Details
      SMD Zener Diodes (Three Terminals) - 200mW
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • MMSZ5229AHEZener diode, Galaxy MicroelectronicsZener diodeNot recordedGalaxy Microelectronics
      What it is
      Zener diode
      Maker
      Galaxy Microelectronics
      Package
      Not recorded
      Pins
      Not recorded
      Details
      4.3V, 500mW, Surface Mount Zener Diodes
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as D4

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.