Skip to content

SMD code D

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • NCT72DMNDFNTemperature sensor, onsemiTemperature sensorDFNNot recordedonsemi
    What it is
    Temperature sensor
    Maker
    onsemi
    Package
    DFN
    Pins
    Not recorded
    Details
     1   C Temperature Monitor with Series Resistance Cancellation
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • NCT1008DMN3DFNTemperature sensor, onsemiTemperature sensorDFNNot recordedonsemi
    What it is
    Temperature sensor
    Maker
    onsemi
    Package
    DFN
    Pins
    Not recorded
    Details
     1  C Temperature Monitor with Series Resistance Cancellation
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • NCT1008DMT3WSONTemperature sensor, onsemiTemperature sensorWSONNot recordedonsemi
    What it is
    Temperature sensor
    Maker
    onsemi
    Package
    WSON
    Pins
    Not recorded
    Details
     1  C Temperature Monitor with Series Resistance Cancellation
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • NL17SH04P5SOT-953Logic gate, 5 pins, onsemiLogic gateSOT-9535 pinsonsemi
    What it is
    Logic gate
    Maker
    onsemi
    Package
    SOT-953
    Pins
    5
    Details
    Single Inverter
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • NL17SZ07P5SOT-953Logic gate, 5 pins, onsemiLogic gateSOT-9535 pinsonsemi
    What it is
    Logic gate
    Maker
    onsemi
    Package
    SOT-953
    Pins
    5
    Details
    Single Non-Inverting Buffer with Open Drain Output
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • NSBA144WF3SOT-1123Digital transistor (PNP, resistors built in), 3 pins, onsemiDigital transistor (PNP, resistors built in)SOT-11233 pinsonsemi
    What it is
    Digital transistor (PNP, resistors built in)
    Maker
    onsemi
    Package
    SOT-1123
    Pins
    3
    Details
    Digital Transistors (BRT) R1 = 47 k  , R2 = 22 k 
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • PAM08SD2312SOD-323ESD protection diode, 2 pins, ProTek DevicesESD protection diodeSOD-3232 pinsProTek Devices
    What it is
    ESD protection diode
    Maker
    ProTek Devices
    Package
    SOD-323
    Pins
    2
    Details
    High Powered TVS Arrays
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • PJSD12TMSOD-923ESD protection diode, 2 pins, PanjitESD protection diodeSOD-9232 pinsPanjit
    What it is
    ESD protection diode
    Maker
    Panjit
    Package
    SOD-923
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • 7 more parts have no package on record
    • NL17SZ08MU1Logic gate, onsemiLogic gateNot recordedNot recordedonsemi
      What it is
      Logic gate
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Single 2-Input AND Gate
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • NL27WZ17MU3Logic gate, onsemiLogic gateNot recordedNot recordedonsemi
      What it is
      Logic gate
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Schmitt Trigger Buffer, Dual, Non-Inverting
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • NSBC144EDP6Digital transistor (NPN, resistors built in), onsemiDigital transistor (NPN, resistors built in)Not recordedNot recordedonsemi
      What it is
      Digital transistor (NPN, resistors built in)
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Dual NPN Bias Resistor Transistors R1 = 47 k  , R2 = 47 k 
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Digital transistor.

    • NSR05301MX4Schottky diode, onsemiSchottky diodeNot recordedNot recordedonsemi
      What it is
      Schottky diode
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Trench-based Schottky Diode, 500 mA, 30 V
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Schottky diode.

    • NTND31015NZDual N-channel MOSFET, onsemiDual N-channel MOSFETNot recordedNot recordedonsemi
      What it is
      Dual N-channel MOSFET
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      MOSFET - Dual, N - Channel, Small Signal, 0.65 mmx0.90mmx0.4mm
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: N-channel MOSFET pair.

    • NTNS3A91PZP-channel MOSFET, onsemiP-channel MOSFETNot recordedNot recordedonsemi
      What it is
      P-channel MOSFET
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      MOSFET - Single, P-Channel, Small Signal, 0.62 x 0.62 x 0.4 mm
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: P-channel MOSFET.

    • PHS512ESD protection diode, ProTek DevicesESD protection diodeNot recordedNot recordedProTek Devices
      What it is
      ESD protection diode
      Maker
      ProTek Devices
      Package
      Not recorded
      Pins
      Not recorded
      Details
      High Powered Surge Protection TVS Array
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: TVS or ESD protection diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

N-channel MOSFET pair

Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

P-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.

1 identification has been run against this marking.