Skip to content
WhatSMDSign in

SMD code G11 in SMB

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

1 part in SMB is printed G11

Not sure which one you have?

Answer up to 4 quick questions and these 2 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • STPS1H100USMBSchottky diode, 2 pins, SGS-Thomson MicroelectronicsSchottky diode2 pinsSGS-Thomson Microelectronics
    What it is
    Schottky diode
    Maker
    SGS-Thomson Microelectronics
    Package
    SMB
    Pins
    2
    Details
    Diode: SBR, 100V, 1A, Vf<0.62V(1A)
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 1 more part has no package on record. Nothing rules it out, so it stays.
    • ADCMP581BCP-R216 pins, Analog DevicesNot recorded16 pinsAnalog Devices
      What it is
      Not recorded
      Maker
      Analog Devices
      Package
      Not recorded
      Pins
      16
      Source
      Published code list

      Is it dead? The meter test is below: This part.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as G11

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with G11

For a marking with its end worn or burnt off. Each code has a page of its own.

Codes not listed here are printed on 8 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.