SMD code G6S
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
7 parts are printed G6S
Not sure which one you have?
Answer up to 4 quick questions and these 7 parts are ranked, with a meter test that settles it. It works on a dead part too.
BAR63-06SOT-23PIN diode, 3 pins, InfineonPIN diodeSOT-233 pinsInfineon
- What it is
- PIN diode
- Maker
- Infineon
- Package
- SOT-23
- Pins
- 3
- Details
- dual ca 3GHz pin
- Source
- Published code list
Is it dead? The meter test is below: PIN diode or varicap.
BAR63-06WSOT-323PIN diode, 3 pins, InfineonPIN diodeSOT-3233 pinsInfineon
- What it is
- PIN diode
- Maker
- Infineon
- Package
- SOT-323
- Pins
- 3
- Details
- dual ca 3GHz pin
- Source
- Published code list
Is it dead? The meter test is below: PIN diode or varicap.
S-80922CLMC-G6ST2SOT-23-5Voltage supervisor, 5 pins, ABLICVoltage supervisorSOT-23-55 pinsABLIC
- What it is
- Voltage supervisor
- Maker
- ABLIC
- Package
- SOT-23-5
- Pins
- 5
- Details
- Voltage detector IC: 2.2V±2%, -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
S-80922CLNB-G6ST2SOT-343Voltage supervisor, 4 pins, ABLICVoltage supervisorSOT-3434 pinsABLIC
- What it is
- Voltage supervisor
- Maker
- ABLIC
- Package
- SOT-343
- Pins
- 4
- Details
- Voltage detector IC: 2.2V±2%, -Reset PPO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
3 more parts have no package on record
AZV331KTR-G1Comparator, Diodes IncorporatedComparatorNot recordedNot recordedDiodes Incorporated
- What it is
- Comparator
- Maker
- Diodes Incorporated
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
S-80922CLPF-G6ST2Voltage supervisor, Seiko InstrumentsVoltage supervisorNot recordedNot recordedSeiko Instruments
- What it is
- Voltage supervisor
- Maker
- Seiko Instruments
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Voltage detector IC: 2.2V±2%, -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
S-80922CLPF-G6STF4 pins, ABLICNot recordedNot recorded4 pinsABLIC
- What it is
- Not recorded
- Maker
- ABLIC
- Package
- Not recorded
- Pins
- 4
- Source
- Published code list
Is it dead? The meter test is below: This part.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PIN diode or varicap
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.6 to 0.9 V anode to cathode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as G6S
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 17 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.