Skip to content

SMD code HX

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BZT52B15WTSOD-523Zener diode, 2 pins, Taitron ComponentsZener diodeSOD-5232 pinsTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SOD-523
    Pins
    2
    Details
    Zener diode: 14.70..15.30V, Izt=5.0mA, 200mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • CD214A-T10ASMATVS diode, 2 pins, BournsTVS diodeSMA2 pinsBourns
    What it is
    TVS diode
    Maker
    Bourns
    Package
    SMA
    Pins
    2
    Details
    TVS: 10V, 23.5A, 400W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • HSMS280MSOT-3636 pins, BroadcomNot recordedSOT-3636 pinsBroadcom
    What it is
    Not recorded
    Maker
    Broadcom
    Package
    SOT-363
    Pins
    6
    Details
    cc quad schottky
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • MAX6315US50D3-TSOT-1434 pins, Analog DevicesNot recordedSOT-1434 pinsAnalog Devices
    What it is
    Not recorded
    Maker
    Analog Devices
    Package
    SOT-143
    Pins
    4
    Details
    CMOS-IC: Voltage Detector 5V, MR, -Reset ODO, 140ms
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • MM5ZB15HSOD-523Zener diode, 2 pins, Zowie TechnologyZener diodeSOD-5232 pinsZowie Technology
    What it is
    Zener diode
    Maker
    Zowie Technology
    Package
    SOD-523
    Pins
    2
    Details
    Zener diode: 14.7..15.3V, Zzt=40, Izt=5mA, 200mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • MMBZ5237BWSOT-323Zener diode, 3 pins, JinYu semiconductorZener diodeSOT-3233 pinsJinYu semiconductor
    What it is
    Zener diode
    Maker
    JinYu semiconductor
    Package
    SOT-323
    Pins
    3
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • P2SMLJ10A-ASOD-123FTVS diode, 2 pins, YeashinTVS diodeSOD-123F2 pinsYeashin
    What it is
    TVS diode
    Maker
    Yeashin
    Package
    SOD-123F
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=10.0V, Vbr=11.10..12.30V, Ipp=11.8A, 200W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • P4SMAJ10ASMATVS diode, 2 pins, PanjitTVS diodeSMA2 pinsPanjit
    What it is
    TVS diode
    Maker
    Panjit
    Package
    SMA
    Pins
    2
    Details
    SMD TVS - 400W
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • PZU6.8B3SOD-323Zener diode, 2 pins, NXPZener diodeSOD-3232 pinsNXP
    What it is
    Zener diode
    Maker
    NXP
    Package
    SOD-323
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • PZU33BLSOD-882Zener diode, 2 pins, NXPZener diodeSOD-8822 pinsNXP
    What it is
    Zener diode
    Maker
    NXP
    Package
    SOD-882
    Pins
    2
    Details
    Zener diode: 31..35V, Zzt=40(Iz=5mA), 250mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 5 more parts have no package on record
    • BU4830GVoltage supervisor, ROHMVoltage supervisorNot recordedNot recordedROHM
      What it is
      Voltage supervisor
      Maker
      ROHM
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS-IC: Voltage Detector 3V, -Reset Open drain output
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • IXD5127C50BNRVoltage supervisor, IXYSVoltage supervisorNot recordedNot recordedIXYS
      What it is
      Voltage supervisor
      Maker
      IXYS
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Voltage detector IC: 5.0V±0.8%, -Reset PPO, -MR, 100ms Rt delay
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • IXD5127N50GNRVoltage supervisor, IXYSVoltage supervisorNot recordedNot recordedIXYS
      What it is
      Voltage supervisor
      Maker
      IXYS
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Voltage detector IC: 5.0V±0.8%, +Reset ODO, -MR, 100ms Rt delay
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • LT4ME10ATVS diode, Lite-On SemiconductorTVS diodeNot recordedNot recordedLite-On Semiconductor
      What it is
      TVS diode
      Maker
      Lite-On Semiconductor
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Transient voltage supressor: Vrwm=10V, Vbr=11.1..12.3V, Ipp=23.5A, 400W(1ms)
      Source
      Published code list

      Is it dead? The meter test is below: TVS or ESD protection diode.

    • P2SMSJ10ATVS diode, YeashinTVS diodeNot recordedNot recordedYeashin
      What it is
      TVS diode
      Maker
      Yeashin
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Transient voltage supressor: Vrwm=10V, Vbr=11.1..12.3V, Ipp=11.8A, 200W(1ms)
      Source
      Published code list

      Is it dead? The meter test is below: TVS or ESD protection diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.