Skip to content

SMD code I4 in SMB

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

1 part in SMB is printed I4

Not sure which one you have?

Answer up to 4 quick questions and these 3 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • SK15BSMBSchottky diode, 2 pins, Fagor ElectronicaSchottky diode2 pinsFagor Electronica
    What it is
    Schottky diode
    Maker
    Fagor Electronica
    Package
    SMB
    Pins
    2
    Details
    Diode: SBR, 50V, 1A, Vf<0.75V(1A)
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 2 more parts have no package on record. Nothing rules them out, so they stay.
    • SGM8477-1GXUWQ10GOperational amplifier, 10 pins, SG MicroOperational amplifier10 pinsSG Micro
      What it is
      Operational amplifier
      Maker
      SG Micro
      Package
      Not recorded
      Pins
      10
      Details
      SGM8477-1 1.8V to 5.5V, Low Noise, Zero-Drift Difference Amplifiers
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • LM48555TLNational SemiconductorNot recordedNot recordedNational Semiconductor
      What it is
      Not recorded
      Maker
      National Semiconductor
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Linear IC: APA, BTL, 2.7..5.5V, 15.7Vp-p, ceramic speaker, shutdown
      Source
      Published code list

      Is it dead? The meter test is below: Ceramic capacitor.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Ceramic capacitor

Ohms range across it, and a capacitance range with it lifted.

Working, it reads

On the ohms range it reads open, or climbs to open as it charges. Lifted, a capacitance range reads close to its value.

Dead, it reads

  • Near 0 Ω, or a few ohms: shorted. The usual failure, often from a crack caused by board flex or heat, and it can come and go.
  • A steady resistance, kilohms rather than open: cracked and leaking.
  • Lifted, far below its value on a capacitance range: cracked open or drifted. Less common than a short, but it happens.
On the board
a shorted capacitor shorts its whole rail, so every capacitor on that rail reads the same short. Lift one end, or feed the rail from a current-limited supply and feel which part warms up.
Compare:
Chip capacitors are mostly unmarked, so the value comes from the schematic or the same position on a working board.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as I4

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes not listed here are printed on 2 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.