Skip to content

SMD code I8

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

62 parts are printed I8

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BZD17C7V5PSOD-123FZener diode, 2 pins, VishayZener diodeSOD-123F2 pinsVishay
    What it is
    Zener diode
    Maker
    Vishay
    Package
    SOD-123F
    Pins
    2
    Details
    7.5 V Zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • BZX584C5V6SOD-523Zener diode, 2 pins, Blue RocketZener diodeSOD-5232 pinsBlue Rocket
    What it is
    Zener diode
    Maker
    Blue Rocket
    Package
    SOD-523
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • MM5Z5V6SOD-523Zener diode, 2 pins, YFWZener diodeSOD-5232 pinsYFW
    What it is
    Zener diode
    Maker
    YFW
    Package
    SOD-523
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • MM5Z5V6BSOD-523Zener diode, 2 pins, RectronZener diodeSOD-5232 pinsRectron
    What it is
    Zener diode
    Maker
    Rectron
    Package
    SOD-523
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • BL8555-18IQSOT-353LDO regulator, 5 pins, Shanghai BellingLDO regulatorSOT-3535 pinsShanghai Belling
    What it is
    LDO regulator
    Maker
    Shanghai Belling
    Package
    SOT-353
    Pins
    5
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 450mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • BL8555-18IRASOT-23-5LDO regulator, 5 pins, Shanghai BellingLDO regulatorSOT-23-55 pinsShanghai Belling
    What it is
    LDO regulator
    Maker
    Shanghai Belling
    Package
    SOT-23-5
    Pins
    5
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 450mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • BL8555-18IRBSOT-23-5LDO regulator, 5 pins, Shanghai BellingLDO regulatorSOT-23-55 pinsShanghai Belling
    What it is
    LDO regulator
    Maker
    Shanghai Belling
    Package
    SOT-23-5
    Pins
    5
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 450mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • BL8555-18UQSOT-353LDO regulator, 5 pins, Shanghai BellingLDO regulatorSOT-3535 pinsShanghai Belling
    What it is
    LDO regulator
    Maker
    Shanghai Belling
    Package
    SOT-353
    Pins
    5
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 450mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • BL8555-18URASOT-23-5LDO regulator, 5 pins, Shanghai BellingLDO regulatorSOT-23-55 pinsShanghai Belling
    What it is
    LDO regulator
    Maker
    Shanghai Belling
    Package
    SOT-23-5
    Pins
    5
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 450mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • BL8555-18URBSOT-23-5LDO regulator, 5 pins, Shanghai BellingLDO regulatorSOT-23-55 pinsShanghai Belling
    What it is
    LDO regulator
    Maker
    Shanghai Belling
    Package
    SOT-23-5
    Pins
    5
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 450mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • 5 more parts have no package on record
    • BZT52C5V6KZener diode, Taiwan SemiconductorZener diodeNot recordedNot recordedTaiwan Semiconductor
      What it is
      Zener diode
      Maker
      Taiwan Semiconductor
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • MM5Z5V6-Q1Zener diode, Formosa MicrosemiZener diodeNot recordedNot recordedFormosa Microsemi
      What it is
      Zener diode
      Maker
      Formosa Microsemi
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • MMBFJ108JFET, onsemiJFETNot recordedNot recordedonsemi
      What it is
      JFET
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      N-Channel JFET J109
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: JFET.

    • SGM897AXUDL6GVoltage supervisor, 6 pins, SG MicroVoltage supervisorNot recorded6 pinsSG Micro
      What it is
      Voltage supervisor
      Maker
      SG Micro
      Package
      Not recorded
      Pins
      6
      Details
      Ultra-Small, Supervisory Circuits with Adjustable Sequencing
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • SGM2041-2.8XGLDO regulator, 4 pins, SG MicroLDO regulatorNot recorded4 pinsSG Micro
      What it is
      LDO regulator
      Maker
      SG Micro
      Package
      Not recorded
      Pins
      4
      Details
      2.8 V output, 300mA, Ultra-Low Noise, Low Dropout, RF Linear Regulator in Ultra-Thin Package
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Voltage regulator.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

JFET

Ohms range for drain to source, diode range for the gate, part lifted.

Working, it reads

Drain to source conducts both ways at a few hundred ohms, depending on the part, and some meters beep on it. The gate reads one junction to drain and to source, about 0.6 to 0.7 V, and open the other way.

Dead, it reads

  • The gate the same both ways to drain or source, near 0 V with a continuous beep: gate shorted.
  • Drain to source open: the channel has failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
Drain to source resistance varies from part to part. An identical part elsewhere on the board shows what is normal.
Watch for:
A good channel can beep like a short between drain and source. That is normal; the gate junction says whether it has failed.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as I8

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes not listed here are printed on 22 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.