Skip to content

SMD code J5 in SOD-123F

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 27 parts are ranked, with a meter test that settles it. It works on a dead part too.

12 parts have no package on record. Nothing rules them out, so they stay.

  • MMBZ5250BWSZener diode, Taitron ComponentsZener diodeNot recordedTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    Not recorded
    Pins
    Not recorded
    Details
    SMD Zener Diodes (Three Terminals) - 200mW
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • MMSZ5250AHEZener diode, Galaxy MicroelectronicsZener diodeNot recordedGalaxy Microelectronics
    What it is
    Zener diode
    Maker
    Galaxy Microelectronics
    Package
    Not recorded
    Pins
    Not recorded
    Details
    20V, 500mW, Surface Mount Zener Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • SGM2045-1.00XGLDO regulator, 4 pins, SG MicroLDO regulator4 pinsSG Micro
    What it is
    LDO regulator
    Maker
    SG Micro
    Package
    Not recorded
    Pins
    4
    Details
    1.00 V output, 300mA, Low VIN, Ultra-Low Noise and High PSRR Linear Regulator
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Voltage regulator.

  • 2SK3230J53 pins, RenesasNot recorded3 pinsRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    Not recorded
    Pins
    3
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • 2SK3653J53 pins, RenesasNot recorded3 pinsRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    Not recorded
    Pins
    3
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • AD8314ACP-WP8 pins, Analog DevicesNot recorded8 pinsAnalog Devices
    What it is
    Not recorded
    Maker
    Analog Devices
    Package
    Not recorded
    Pins
    8
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • AP8821N-15GIVoltage supervisor, Anwell SemiconductorVoltage supervisorNot recordedAnwell Semiconductor
    What it is
    Voltage supervisor
    Maker
    Anwell Semiconductor
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Voltage detector IC: 1.5V±2%, -Reset ODO, H-free
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • AP8821N-15GSVoltage supervisor, Anwell SemiconductorVoltage supervisorNot recordedAnwell Semiconductor
    What it is
    Voltage supervisor
    Maker
    Anwell Semiconductor
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Voltage detector IC: 1.5V±2%, -Reset ODO, H-free
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • AP8821N-15PIVoltage supervisor, Anwell SemiconductorVoltage supervisorNot recordedAnwell Semiconductor
    What it is
    Voltage supervisor
    Maker
    Anwell Semiconductor
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Voltage detector IC: 1.5V±2%, -Reset ODO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • AP8821N-15PSVoltage supervisor, Anwell SemiconductorVoltage supervisorNot recordedAnwell Semiconductor
    What it is
    Voltage supervisor
    Maker
    Anwell Semiconductor
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Voltage detector IC: 1.5V±2%, -Reset ODO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • NC7SP02LFairchild SemiconductorNot recordedNot recordedFairchild Semiconductor
    What it is
    Not recorded
    Maker
    Fairchild Semiconductor
    Package
    Not recorded
    Pins
    Not recorded
    Details
    CMOS logic IC: 2-input NOR gate
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • RN1966FSToshibaNot recordedNot recordedToshiba
    What it is
    Not recorded
    Maker
    Toshiba
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Si-npn-Digi: Dual, Sw, 20V, 50mA, 50mW, 250MHz, R1/R2=4k7/47k
    Source
    Published code list

    Is it dead? The meter test is below: This part.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.