SMD code JYp
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
The last letter, p, is lower case, which on NXP and Philips parts is a date or factory code, so it was set aside and JY was searched.
42 parts are printed JYp
Not sure which one you have?
Answer up to 4 quick questions and these 42 parts are ranked, with a meter test that settles it. It works on a dead part too.
BAV199SOT-23Switching diode, 3 pins, InfineonSwitching diodeSOT-233 pinsInfineon
- What it is
- Switching diode
- Maker
- Infineon
- Package
- SOT-23
- Pins
- 3
- Details
- 0.14A, 85V, Surface Mount Small Signal Switching Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BAV199,215SOT-23Switching diode, 3 pins, HXYSwitching diodeSOT-233 pinsHXY
- What it is
- Switching diode
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- Switching diode, 70 V, 0.5 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BAV199LSOT-23Switching diode, 3 pins, onsemiSwitching diodeSOT-233 pinsonsemi
- What it is
- Switching diode
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- Dual Series Switching Diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BAV199WSOT-323Switching diode, 3 pins, DiotecSwitching diodeSOT-3233 pinsDiotec
- What it is
- Switching diode
- Maker
- Diotec
- Package
- SOT-323
- Pins
- 3
- Details
- SMD Small Signal Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BZX84C5V1CC-HFSOT-23Zener diode, 3 pins, ComchipZener diodeSOT-233 pinsComchip
- What it is
- Zener diode
- Maker
- Comchip
- Package
- SOT-23
- Pins
- 3
- Details
- 5.1 V 0.35 mW zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
GSBAV199SOT-23Switching diode, 3 pins, Good-ArkSwitching diodeSOT-233 pinsGood-Ark
- What it is
- Switching diode
- Maker
- Good-Ark
- Package
- SOT-23
- Pins
- 3
- Details
- Switching diode, 70 V, 500 mA
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
SBAV199LSOT-23Switching diode, 3 pins, onsemiSwitching diodeSOT-233 pinsonsemi
- What it is
- Switching diode
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- Dual Series Switching Diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
TBAV199SOT-23Switching diode, 3 pins, Galaxy MicroelectronicsSwitching diodeSOT-233 pinsGalaxy Microelectronics
- What it is
- Switching diode
- Maker
- Galaxy Microelectronics
- Package
- SOT-23
- Pins
- 3
- Details
- 0.14A, 85V, Surface Mount Small Signal Switching Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
1.5SMC120CASMCTVS diode, 2 pins, PanjitTVS diodeSMC2 pinsPanjit
- What it is
- TVS diode
- Maker
- Panjit
- Package
- SMC
- Pins
- 2
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
2SJ244SOT-89P-channel MOSFET, 3 pins, RenesasP-channel MOSFETSOT-893 pinsRenesas
- What it is
- P-channel MOSFET
- Maker
- Renesas
- Package
- SOT-89
- Pins
- 3
- Details
- p-MOS*-e: V-MOS, LogL, 12V, 2A, <0,9Ω(0,5A), integr. Rgate
- Source
- Published code list
Is it dead? The meter test is below: P-channel MOSFET.
2SK208-YSOT-233 pins, ToshibaNot recordedSOT-233 pinsToshiba
- What it is
- Not recorded
- Maker
- Toshiba
- Package
- SOT-23
- Pins
- 3
- Details
- FET n-type: AF-Amp, 50V, 10mA, 100mW, Idss=1.2..3mA
- Source
- Published code list
Is it dead? The meter test is below: MOSFET.
2SK208YSOT-233 pins, ToshibaNot recordedSOT-233 pinsToshiba
- What it is
- Not recorded
- Maker
- Toshiba
- Package
- SOT-23
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: This part.
2SK879-YSOT-3233 pins, ToshibaNot recordedSOT-3233 pinsToshiba
- What it is
- Not recorded
- Maker
- Toshiba
- Package
- SOT-323
- Pins
- 3
- Details
- FET n-type: AF-Amp, 50V, 10mA, 100mW, Idss=1.2..3mA, Up<5V
- Source
- Published code list
Is it dead? The meter test is below: MOSFET.
2 more parts have no package on record
PG12DBUL2ESD protection diode, KECESD protection diodeNot recordedNot recordedKEC
- What it is
- ESD protection diode
- Maker
- KEC
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
RQ6E060ATP-channel MOSFET, ROHMP-channel MOSFETNot recordedNot recordedROHM
- What it is
- P-channel MOSFET
- Maker
- ROHM
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Pch -30V -6A Middle Power MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
P-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as JYp
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with JYp
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 22 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.