SMD code M1p
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
The last letter, p, is lower case, which on NXP and Philips parts is a date or factory code, so it was set aside and M1 was searched.
181 parts are printed M1p
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
MM3Z5256BSOD-323Zener diode, 2 pins, Extensive TechnologyZener diodeSOD-3232 pinsExtensive Technology
- What it is
- Zener diode
- Maker
- Extensive Technology
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 30V±5%, Izt=4.2mA, Zzt=49, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MMBZ5256BTSOT-5233 pins, Diodes IncorporatedNot recordedSOT-5233 pinsDiodes Incorporated
- What it is
- Not recorded
- Maker
- Diodes Incorporated
- Package
- SOT-523
- Pins
- 3
- Details
- Z-diode: 30V±5%, Zzt=49Ω, 150mW
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
MMBZ5256BVSOD-523Zener diode, 2 pins, PanjitZener diodeSOD-5232 pinsPanjit
- What it is
- Zener diode
- Maker
- Panjit
- Package
- SOD-523
- Pins
- 2
- Details
- Zener diode: 30V±5%, Izt=4.2mA, Zzt=49, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MMSZ5256SOD-123Zener diode, 2 pins, VishayZener diodeSOD-1232 pinsVishay
- What it is
- Zener diode
- Maker
- Vishay
- Package
- SOD-123
- Pins
- 2
- Details
- 30 V Zener diode
- Source
- An older or alternative marking, from a published code list
Is it dead? The meter test is below: Zener diode.
MMSZ5256B-FSOD-123FZener diode, 2 pins, Taitron ComponentsZener diodeSOD-123F2 pinsTaitron Components
- What it is
- Zener diode
- Maker
- Taitron Components
- Package
- SOD-123F
- Pins
- 2
- Details
- Zener diode: 28.50 31.50V, Izt=4.2mA, 500mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
OYD30VT1SOD-123Zener diode, 2 pins, Ouyada ElectronicsZener diodeSOD-1232 pinsOuyada Electronics
- What it is
- Zener diode
- Maker
- Ouyada Electronics
- Package
- SOD-123
- Pins
- 2
- Details
- Zener diode: 28...32V, Izt=5mA, Zzt=80, 500mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
R1121N311ASOT-23-55 pins, Nisshinbo Micro DevicesNot recordedSOT-23-55 pinsNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- SOT-23-5
- Pins
- 5
- Details
- VR-IC: LDO, LN, -CE, 3.1V±2%, 150mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
R1151N002CSOT-23-66 pins, Nisshinbo Micro DevicesNot recordedSOT-23-66 pinsNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- SOT-23-6
- Pins
- 6
- Details
- VR-IC: Boost, CE, 2V±2%, 150mA, Vdet ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
R3111N412CSOT-233 pins, Nisshinbo Micro DevicesNot recordedSOT-233 pinsNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 4,1V±2.0%, Reset Open drain output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
R3111Q211ASOT-1434 pins, Nisshinbo Micro DevicesNot recordedSOT-1434 pinsNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- SOT-143
- Pins
- 4
- Details
- CMOS-IC: Voltage Detector 2,1V±2.0%, Reset Push-pull output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
R3116Q181ASOT-343Voltage supervisor, 4 pins, RicohVoltage supervisorSOT-3434 pinsRicoh
- What it is
- Voltage supervisor
- Maker
- Ricoh
- Package
- SOT-343
- Pins
- 4
- Details
- Voltage detector IC: 1.8V±0.8%, -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
R3117K183ADFNVoltage supervisor, RicohVoltage supervisorDFNNot recordedRicoh
- What it is
- Voltage supervisor
- Maker
- Ricoh
- Package
- DFN
- Pins
- Not recorded
- Details
- Voltage detector IC: 1.8V±1%, -Reset ODO, Sense
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
R3117N201CSOT-23-5Voltage supervisor, 5 pins, RicohVoltage supervisorSOT-23-55 pinsRicoh
- What it is
- Voltage supervisor
- Maker
- Ricoh
- Package
- SOT-23-5
- Pins
- 5
- Details
- Voltage detector IC: 2.0V±1%, -Reset PPO, Sense
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
2 more parts have no package on record
R1100D111CNisshinbo Micro DevicesNot recordedNot recordedNot recordedNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- Not recorded
- Pins
- Not recorded
- Details
- VR-IC: U-low Icc, 1.1V±2%, 180mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
R1131D111BNisshinbo Micro DevicesNot recordedNot recordedNot recordedNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- Not recorded
- Pins
- Not recorded
- Details
- VR-IC: LDO, -CE, 1.1V±2%, 300mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.