SMD marking

Nin SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

12 parts are printed N

Not sure which one you have?

Answer up to 4 quick questions and these 12 parts are ranked, with a meter test that settles it. It works on a dead part too.

BCW66FSOT-23Transistor, 3 pins, DiotecTransistor3 pinsDiotec
What it is
Transistor
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD General Purpose NPN Transistors
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or its base leg off the pad.
Working, it reads
From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
Only one junction reads, or none: a junction has failed open. It then looks like a diode.
A reading the wrong way round, where it should be open: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BCW66F, opens in a new tab
11 more parts have no package on record. Nothing rules them out, so they stay.
- AOZ8S204BLS-38ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8S204BLS-38, opens in a new tab
- AOZ1356LI-06Load switch, Alpha & Omega SemiconductorLoad switchNot recordedAlpha & Omega Semiconductor
  What it is
  Load switch
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  USB Type-C protection switch
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, black probe on ground.
  Working, it reads
  Switched on, the output pin sits at the input voltage. Switched off, it sits near 0 V.
  Dead, it reads
  Output at the input voltage while switched off: the pass element has shorted.
  Input present and switched on, no output: failed open, or shut down into a shorted load. Power off and measure output to ground.
  On the board:
  An output near 0 Ω to ground is usually the load. Lift the output pin to see which.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The pinout and whether the enable is active high or low differ between parts. The datasheet gives both.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ1356LI-06, opens in a new tab
- AOZ8310DI-02ESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8310DI-02, opens in a new tab
- BAR65-02VPIN diode, InfineonPIN diodeNot recordedInfineon
  What it is
  PIN diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.6 to 0.9 V anode to cathode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BAR65-02V, opens in a new tab
- ESD105-B1-02ELESD protection diode, InfineonESD protection diodeNot recordedInfineon
  What it is
  ESD protection diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESD105-B1-02EL, opens in a new tab
- ESD105-B1-02ELSESD protection diode, InfineonESD protection diodeNot recordedInfineon
  What it is
  ESD protection diode
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESD105-B1-02ELS, opens in a new tab
- IRLML2060N-channel MOSFET, InfineonN-channel MOSFETNot recordedInfineon
  What it is
  N-channel MOSFET
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Details
  60V Single N-Channel HEXFET Power MOSFET in a Micro 3 package
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor IRLML2060, opens in a new tab
- PMEG4002AESFSchottky diode, 2 pins, NexperiaSchottky diode2 pinsNexperia
  What it is
  Schottky diode
  Maker
  Nexperia
  Package
  Not recorded
  Pins
  2
  Details
  40 V, 0.2 A low VF MEGA Schottky barrier rectifier
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PMEG4002AESF, opens in a new tab
- PS1103-D32ESD protection diode, PanjitESD protection diodeNot recordedPanjit
  What it is
  ESD protection diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PS1103-D32, opens in a new tab
- TMP112D1IDPWTemperature sensor, 5 pins, Texas InstrumentsTemperature sensor5 pinsTexas Instruments
  What it is
  Temperature sensor
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  5
  Details
  High-Accuracy, Low-Power, Digital Temperature Sensors With SMBus and Two-Wire Serial Interface in SOT563 and X2SON...
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TMP112D1IDPW, opens in a new tab
- VCUT03B1-DD1ESD protection diode, VishayESD protection diodeNot recordedVishay
  What it is
  ESD protection diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Bidirectional Symmetrical (BiSy) Single Line ESD-Protection Diode in LLP1006-2M
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor VCUT03B1-DD1, opens in a new tab

38 more parts have codes that begin with N

Codes that begin with N

For a marking with its end worn or burnt off. Each one shows its full printed code.

all SOT-23, 3 pins. What differs:

2BZX84C4V3printed NASOT-23Zener diode, DiotecZener diodeDiotec
Printed NA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C4V3, opens in a new tab
2BZX84C4V7printed NBSOT-23Zener diode, DiotecZener diodeDiotec
Printed NB. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C4V7, opens in a new tab
2BZX84C5V1printed NCSOT-23Zener diode, DiotecZener diodeDiotec
Printed NC. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C5V1, opens in a new tab
2BZX84C5V6printed NDSOT-23Zener diode, DiotecZener diodeDiotec
Printed ND. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C5V6, opens in a new tab
2BZX84C6V2printed NESOT-23Zener diode, DiotecZener diodeDiotec
Printed NE. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C6V2, opens in a new tab
2BZX84C6V8printed NFSOT-23Zener diode, DiotecZener diodeDiotec
Printed NF. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C6V8, opens in a new tab
2BZX84C7V5printed NHSOT-23Zener diode, DiotecZener diodeDiotec
Printed NH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C7V5, opens in a new tab
2BZX84C8V2printed NJSOT-23Zener diode, DiotecZener diodeDiotec
Printed NJ. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C8V2, opens in a new tab
2BZX84C9V1printed NKSOT-23Zener diode, DiotecZener diodeDiotec
Printed NK. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C9V1, opens in a new tab
2BZX84C10printed NMSOT-23Zener diode, DiotecZener diodeDiotec
Printed NM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C10, opens in a new tab
2BZX84C11printed NNSOT-23Zener diode, DiotecZener diodeDiotec
Printed NN. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C11, opens in a new tab
2BZX84C12printed NPSOT-23Zener diode, DiotecZener diodeDiotec
Printed NP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C12, opens in a new tab
2BZX84C13printed NXSOT-23Zener diode, DiotecZener diodeDiotec
Printed NX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C13, opens in a new tab
2BZX84C15printed NYSOT-23Zener diode, DiotecZener diodeDiotec
Printed NY. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C15, opens in a new tab
2BZX84C16printed NZSOT-23Zener diode, DiotecZener diodeDiotec
Printed NZ. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2BZX84C16, opens in a new tab
2SCR544Rprinted NSSOT-23Transistor, DiotecTransistorDiotec
Printed NS. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Transistor
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD High Current NPN Transistors
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or its base leg off the pad.
Working, it reads
From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
Only one junction reads, or none: a junction has failed open. It then looks like a diode.
A reading the wrong way round, where it should be open: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 2SCR544R, opens in a new tab
AOSS21329printed NBSOT-23P-channel MOSFET, Alpha & Omega SemiconductorP-channel MOSFETAlpha & Omega Semiconductor
Printed NB. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOSS21329, opens in a new tab
AOSS32128printed NASOT-23MOSFET, Alpha & Omega SemiconductorMOSFETAlpha & Omega Semiconductor
Printed NA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOT-23
Pins
3
Details
Low-voltage (12-30 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOSS32128, opens in a new tab
BZX84C5V1printed N8SOT-23Zener diode, DiotecZener diodeDiotec
Printed N8. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84C5V1, opens in a new tab
BZX84C24printed N9SOT-23Zener diode, DiotecZener diodeDiotec
Printed N9. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZX84C24, opens in a new tab
DMN1019USNprinted N7SOT-23N-channel MOSFET, Diodes IncorporatedN-channel MOSFETDiodes Incorporated
Printed N7. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
N-channel MOSFET
Maker
Diodes Incorporated
Package
SOT-23
Pins
3
Details
12 V N-channel enhancement mode MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor DMN1019USN, opens in a new tab
ESDBNC15VS2printed NC15SOT-23ESD protection diode, JSCJESD protection diodeJSCJ
Printed NC15. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
ESD protection diode
Maker
JSCJ
Package
SOT-23
Pins
3
Details
ESD protection diode, VRWM 15 V
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ESDBNC15VS2, opens in a new tab
ESDBNC18VS2printed NC18SOT-23ESD protection diode, JSCJESD protection diodeJSCJ
Printed NC18. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
ESD protection diode
Maker
JSCJ
Package
SOT-23
Pins
3
Details
ESD protection diode, VRWM 18 V
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ESDBNC18VS2, opens in a new tab
ESDBND24VS2printed ND24SOT-23ESD protection diode, JSCJESD protection diodeJSCJ
Printed ND24. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
ESD protection diode
Maker
JSCJ
Package
SOT-23
Pins
3
Details
ESD protection diode, VRWM 24 V
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ESDBND24VS2, opens in a new tab
MMBZ5261Aprinted N1SOT-23Zener diode, PanjitZener diodePanjit
Printed N1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5261A, opens in a new tab
MMBZ5261Bprinted N1SOT-23Zener diode, PanjitZener diodePanjit
Printed N1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5261B, opens in a new tab
MMBZ5261B-AUprinted N1SOT-23Zener diode, PanjitZener diodePanjit
Printed N1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5261B-AU, opens in a new tab
MMBZ5262Aprinted N2SOT-23Zener diode, PanjitZener diodePanjit
Printed N2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5262A, opens in a new tab
MMBZ5262Bprinted N2SOT-23Zener diode, PanjitZener diodePanjit
Printed N2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5262B, opens in a new tab
MMBZ5262B-AUprinted N2SOT-23Zener diode, PanjitZener diodePanjit
Printed N2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5262B-AU, opens in a new tab
MMBZ5263Bprinted N3SOT-23Zener diode, PanjitZener diodePanjit
Printed N3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5263B, opens in a new tab
MMBZ5264Bprinted N4SOT-23Zener diode, PanjitZener diodePanjit
Printed N4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5264B, opens in a new tab
MMBZ5265Bprinted N5SOT-23Zener diode, PanjitZener diodePanjit
Printed N5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMBZ5265B, opens in a new tab
MMDTD141printed NTSOT-23Digital transistor (resistors built in), DiotecDigital transistor (resistors built in)Diotec
Printed NT. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Digital transistor (resistors built in)
Maker
Diotec
Package
SOT-23
Pins
3
Details
SMD Digital NPN Transistors
Source
From the manufacturer's datasheet
Is it dead?
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
Base to emitter near 0 Ω: failed short.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMDTD141, opens in a new tab
MMFTN490Kprinted NS1SOT-23MOSFET, DiotecMOSFETDiotec
Printed NS1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Diotec
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMFTN490K, opens in a new tab
MMFTN1092Kprinted NL1SOT-23MOSFET, DiotecMOSFETDiotec
Printed NL1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Diotec
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMFTN1092K, opens in a new tab
MMFTN4520printed NX1SOT-23MOSFET, DiotecMOSFETDiotec
Printed NX1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Diotec
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMFTN4520, opens in a new tab
MMFTP3334Kprinted NWSOT-23MOSFET, DiotecMOSFETDiotec
Printed NW. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Diotec
Package
SOT-23
Pins
3
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMFTP3334K, opens in a new tab

Open this in the search to correct a character or try another package.

12 parts are printed N

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with N

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?