SMD code N25
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
N25 on a chip capacitor
250 pF
250 pF capacitor
The n is both the decimal point and the unit: 250 pF.
Check it with a meter
Lift one end and measure it on a capacitance range. A good one reads close to 250 pF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. A failed one usually reads near 0 Ω, or a steady low resistance, on the ohms range, often from a crack. On the board a shorted capacitor shorts its whole rail. A failed reading does not change what to fit: the marking still says 250 pF.
On a transistor or diode body (SOT-23, SOT-89, SOT-23-5), N25 is a part code instead. Those parts are listed below.
28 parts are printed N25
Not sure which one you have?
Answer up to 4 quick questions and these 28 parts are ranked, with a meter test that settles it. It works on a dead part too.
82N25-AE3-5SOT-23Voltage supervisor, 3 pins, UnisonicVoltage supervisorSOT-233 pinsUnisonic
- What it is
- Voltage supervisor
- Maker
- Unisonic
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.5V±2% -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
82N25-AF5-BSOT-23-5Voltage supervisor, 5 pins, UnisonicVoltage supervisorSOT-23-55 pinsUnisonic
- What it is
- Voltage supervisor
- Maker
- Unisonic
- Package
- SOT-23-5
- Pins
- 5
- Details
- Voltage detector IC: 2.5V±2% -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
BL8064CC3TR25SOT-89LDO regulator, 3 pins, Shanghai BellingLDO regulatorSOT-893 pinsShanghai Belling
- What it is
- LDO regulator
- Maker
- Shanghai Belling
- Package
- SOT-89
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 2.5V±2%, 250mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
DDTC125TCASOT-23Digital transistor (NPN, resistors built in), 3 pins, Diodes IncorporatedDigital transistor (NPN, resistors built in)SOT-233 pinsDiodes Incorporated
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- Diodes Incorporated
- Package
- SOT-23
- Pins
- 3
- Details
- dtr npn 50V 0.1A R1 200k 0.2W
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
DDTC125TESOT-523Digital transistor (NPN, resistors built in), 3 pins, Diodes IncorporatedDigital transistor (NPN, resistors built in)SOT-5233 pinsDiodes Incorporated
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- Diodes Incorporated
- Package
- SOT-523
- Pins
- 3
- Details
- dtr npn 50V 0.1A R1 200k 0.15W
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
DDTC125TKASOT-23Digital transistor (NPN, resistors built in), 3 pins, Diodes IncorporatedDigital transistor (NPN, resistors built in)SOT-233 pinsDiodes Incorporated
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- Diodes Incorporated
- Package
- SOT-23
- Pins
- 3
- Details
- dtr npn 50V 0.1A R1 200k 0.2W
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
DDTC125TUASOT-323Digital transistor (NPN, resistors built in), 3 pins, Diodes IncorporatedDigital transistor (NPN, resistors built in)SOT-3233 pinsDiodes Incorporated
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- Diodes Incorporated
- Package
- SOT-323
- Pins
- 3
- Details
- dtr npn 50V 0.1A R1 200k 0.2W
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
LC1208CC3TR25SOT-89LDO regulator, 3 pins, Shanghai LeadChip MicroelectronicsLDO regulatorSOT-893 pinsShanghai LeadChip Microelectronics
- What it is
- LDO regulator
- Maker
- Shanghai LeadChip Microelectronics
- Package
- SOT-89
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 2.5V±2%, 250mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
LDTC125TLT1GSOT-23Digital transistor (NPN, resistors built in), 3 pins, LRCDigital transistor (NPN, resistors built in)SOT-233 pinsLRC
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- LRC
- Package
- SOT-23
- Pins
- 3
- Details
- NPN transistor: Sw., 50V, 100mA, B=100..60, R1=200k
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
LDTC125TWT1GSOT-323Digital transistor (NPN, resistors built in), 3 pins, LRCDigital transistor (NPN, resistors built in)SOT-3233 pinsLRC
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- LRC
- Package
- SOT-323
- Pins
- 3
- Details
- NPN transistor: Sw., 50V, 100mA, B=100..600, R1=200k
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
LN61FN3212MSOT-23Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-233 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 3.2V±2%, +Reset ODO, Rdt=200ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
LN61FN3212PSOT-89Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-893 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-89
- Pins
- 3
- Details
- Voltage detector IC: 3.2V±2%, +Reset ODO, 200ms Rt delay
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
LN809N4311MSOT-23Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-233 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 4.38V±1%, Reset PPO, Rdt=50..200ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
2 more parts have no package on record
LN2502LT1GN-channel MOSFET, LRCN-channel MOSFETNot recordedNot recordedLRC
- What it is
- N-channel MOSFET
- Maker
- LRC
- Package
- Not recorded
- Pins
- Not recorded
- Details
- MOSFET, N-Channel, VDSS 20 V, VGS 12 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
LDTC125TET1GDigital transistor (NPN, resistors built in), LRCDigital transistor (NPN, resistors built in)Not recordedNot recordedLRC
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- LRC
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Digital transistor (bias resistors built in), NPN, IC 100 mA, VCEO 50 V
- Source
- An older or alternative marking, from a published code list
Is it dead? The meter test is below: Digital transistor.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Digital transistor
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
- Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
- From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
- Base to emitter near 0 Ω: failed short.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
- Watch for:
- On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as N25
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with N25
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 8 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.