SMD code N36
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
N36 on a chip capacitor
360 pF
360 pF capacitor
The n is both the decimal point and the unit: 360 pF.
Check it with a meter
Lift one end and measure it on a capacitance range. A good one reads close to 360 pF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. A failed one usually reads near 0 Ω, or a steady low resistance, on the ohms range, often from a crack. On the board a shorted capacitor shorts its whole rail. A failed reading does not change what to fit: the marking still says 360 pF.
On a transistor or diode body (SOT-23-5, SOT-23, SOT-89), N36 is a part code instead. Those parts are listed below.
18 parts are printed N36
Not sure which one you have?
Answer up to 4 quick questions and these 18 parts are ranked, with a meter test that settles it. It works on a dead part too.
82N36-AE3-5SOT-23Voltage supervisor, 3 pins, UnisonicVoltage supervisorSOT-233 pinsUnisonic
- What it is
- Voltage supervisor
- Maker
- Unisonic
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 3.6V±2% -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
82N36-AF5-BSOT-23-5Voltage supervisor, 5 pins, UnisonicVoltage supervisorSOT-23-55 pinsUnisonic
- What it is
- Voltage supervisor
- Maker
- Unisonic
- Package
- SOT-23-5
- Pins
- 5
- Details
- Voltage detector IC: 3.6V±2% -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
BFG520SOT-1434 pins, PhiNot recordedSOT-1434 pinsPhi
- What it is
- Not recorded
- Maker
- Phi
- Package
- SOT-143
- Pins
- 4
- Details
- npn RF 9GHz 70mA
- Source
- Published code list
Is it dead? The meter test is below: This part.
BL8064CC3TR36SOT-89LDO regulator, 3 pins, Shanghai BellingLDO regulatorSOT-893 pinsShanghai Belling
- What it is
- LDO regulator
- Maker
- Shanghai Belling
- Package
- SOT-89
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 3.6V±2%, 250mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
LC1208CC3TR36SOT-89LDO regulator, 3 pins, Shanghai LeadChip MicroelectronicsLDO regulatorSOT-893 pinsShanghai LeadChip Microelectronics
- What it is
- LDO regulator
- Maker
- Shanghai LeadChip Microelectronics
- Package
- SOT-89
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 3.6V±2%, 250mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
LN61FN3342MSOT-23Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-233 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 3.3V±2%, +Reset ODO, Rdt=400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
LN61FN3342PSOT-89Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-893 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-89
- Pins
- 3
- Details
- Voltage detector IC: 3.3V±2%, +Reset ODO, 400ms Rt delay
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
LR8064CC3TR36SOT-89LDO regulator, 3 pins, LRCLDO regulatorSOT-893 pinsLRC
- What it is
- LDO regulator
- Maker
- LRC
- Package
- SOT-89
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 3.6V±2%, 250mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
TC126361ECTSOT-23-5DC-DC converter, 5 pins, MicrochipDC-DC converterSOT-23-55 pinsMicrochip
- What it is
- DC-DC converter
- Maker
- Microchip
- Package
- SOT-23-5
- Pins
- 5
- Details
- DC/DC voltage converter IC: PFM st-up, 3.6V±2.5%, 80mA, 100kHz, Sense
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC61FN3342MSOT-23Voltage supervisor, 3 pins, TorexVoltage supervisorSOT-233 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 3,3V, Reset Open drain output, 400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC61FN3342PSOT-89Voltage supervisor, 3 pins, TorexVoltage supervisorSOT-893 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-89
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 3,3V, Reset Open drain output, 400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC61HN3342MRSOT-23Voltage supervisor, 3 pins, TorexVoltage supervisorSOT-233 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 3.3V±2%, -Reset ODO, Rdt=80..400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC6382E361MSOT-23-5DC-DC converter, 5 pins, TorexDC-DC converterSOT-23-55 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-23-5
- Pins
- 5
- Details
- DC/DC voltage converter IC: PFM st-up, 3.6V±2.5%, 400mA, 100kHz, internal Vdd
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
2 more parts have no package on record
S72N36SFAUK SemiconductorNot recordedNot recordedNot recordedAUK Semiconductor
- What it is
- Not recorded
- Maker
- AUK Semiconductor
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Lin/Digi-IC: Voltage Detector 3,6V, Reset Open collector output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
S72N36UFAUK SemiconductorNot recordedNot recordedNot recordedAUK Semiconductor
- What it is
- Not recorded
- Maker
- AUK Semiconductor
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Lin/Digi-IC: Voltage Detector 3,6V, Reset Open collector output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as N36
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with N36
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 8 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.