Skip to content

SMD code O9

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

5 parts are printed O9

Not sure which one you have?

Answer up to 4 quick questions and these 5 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BZD27C22P-MSOD-123FZener diode, 2 pins, VishayZener diodeSOD-123F2 pinsVishay
    What it is
    Zener diode
    Maker
    Vishay
    Package
    SOD-123F
    Pins
    2
    Details
    22 V Zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SS377SOT-23Schottky diode, 3 pins, ToshibaSchottky diodeSOT-233 pinsToshiba
    What it is
    Schottky diode
    Maker
    Toshiba
    Package
    SOT-23
    Pins
    3
    Details
    2 x 10V 0.1A cc schottky
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 1SS378SOT-323Schottky diode, 3 pins, ToshibaSchottky diodeSOT-3233 pinsToshiba
    What it is
    Schottky diode
    Maker
    Toshiba
    Package
    SOT-323
    Pins
    3
    Details
    0.1A, 15V, Surface Mount Small Signal Schottky Diodes
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 1SS385SOT-4163 pins, ToshibaNot recordedSOT-4163 pinsToshiba
    What it is
    Not recorded
    Maker
    Toshiba
    Package
    SOT-416
    Pins
    3
    Details
    Si-diode: Dual, Schottky, 10V, 100mA
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 1 more part has no package on record
    • 1SS385FSchottky diode, ToshibaSchottky diodeNot recordedNot recordedToshiba
      What it is
      Schottky diode
      Maker
      Toshiba
      Package
      Not recorded
      Pins
      Not recorded
      Details
      2 x 10V 0.1A cc schottky
      Source
      Published code list

      Is it dead? The meter test is below: Schottky diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as O9

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes not listed here are printed on 3 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.