SMD code P1p
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
The last letter, p, is lower case, which on NXP and Philips parts is a date or factory code, so it was set aside and P1 was searched.
112 parts are printed P1p
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
RP114K281B5DFNLDO regulator, RicohLDO regulatorDFNNot recordedRicoh
- What it is
- LDO regulator
- Maker
- Ricoh
- Package
- DFN
- Pins
- Not recorded
- Details
- Linear voltage regulator IC: LDO, 2.85V±1%, 300mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
RP200N211DSOT-23-5LDO regulator, 5 pins, RicohLDO regulatorSOT-23-55 pinsRicoh
- What it is
- LDO regulator
- Maker
- Ricoh
- Package
- SOT-23-5
- Pins
- 5
- Details
- Linear voltage regulator IC: LDO, 2.1V±1.0%, 300mA, +CE, CL, AE(mode)
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
RT1P137PSOT-893 pins, MitNot recordedSOT-893 pinsMit
- What it is
- Not recorded
- Maker
- Mit
- Package
- SOT-89
- Pins
- 3
- Details
- Si-pnp-Digi: Sw, 40V, 1A, 500mW, 150MHz, R1/R2=1k/22K
- Source
- Published code list
Is it dead? The meter test is below: This part.
RT1P141CSOT-233 pins, MitNot recordedSOT-233 pinsMit
- What it is
- Not recorded
- Maker
- Mit
- Package
- SOT-23
- Pins
- 3
- Details
- Si-pnp-Digi: Sw, 50V, 100mA, 150mW, 200MHz, R1/R2=10k/10k
- Source
- Published code list
Is it dead? The meter test is below: This part.
RT1P141MSOT-3233 pins, MitNot recordedSOT-3233 pinsMit
- What it is
- Not recorded
- Maker
- Mit
- Package
- SOT-323
- Pins
- 3
- Details
- Si-pnp-Digi: Sw, 50V, 100mA, 150mW, 200MHz, R1/R2=10k/10k
- Source
- Published code list
Is it dead? The meter test is below: This part.
RT1P141USOT-4163 pins, MitNot recordedSOT-4163 pinsMit
- What it is
- Not recorded
- Maker
- Mit
- Package
- SOT-416
- Pins
- 3
- Details
- Si-pnp-Digi: Sw, 50V, 100mA, 125mW, 200MHz, R1/R2=10k/10k
- Source
- Published code list
Is it dead? The meter test is below: This part.
SGA-9189SOT-893 pins, SirNot recordedSOT-893 pinsSir
- What it is
- Not recorded
- Maker
- Sir
- Package
- SOT-89
- Pins
- 3
- Details
- Lin-IC: Si/Ge RF amplifier, DC..3GHz, 13,2dB (50Ω)
- Source
- Published code list
Is it dead? The meter test is below: RF amplifier.
SP6641AEK-5.0SOT-23DC-DC converter, 3 pins, SipexDC-DC converterSOT-233 pinsSipex
- What it is
- DC-DC converter
- Maker
- Sipex
- Package
- SOT-23
- Pins
- 3
- Details
- Step Up Converter
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
SST201SOT-233 pins, VishayNot recordedSOT-233 pinsVishay
- What it is
- Not recorded
- Maker
- Vishay
- Package
- SOT-23
- Pins
- 3
- Details
- n-FET: AF, LN, 40V, 350mW, Idss=0.2..1mA, Up<1,5V
- Source
- Published code list
Is it dead? The meter test is below: MOSFET.
TC54VN4102ECBSOT-23Voltage supervisor, 3 pins, MicrochipVoltage supervisorSOT-233 pinsMicrochip
- What it is
- Voltage supervisor
- Maker
- Microchip
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 4.1V±2%, -Reset Open drain output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
TC54VN4102MBSOT-89Voltage supervisor, 3 pins, MicrochipVoltage supervisorSOT-893 pinsMicrochip
- What it is
- Voltage supervisor
- Maker
- Microchip
- Package
- SOT-89
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 4.1V±2%, -Reset Open drain output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
TC1186-2.5VCT713SOT-23-5LDO regulator, 5 pins, MicrochipLDO regulatorSOT-23-55 pinsMicrochip
- What it is
- LDO regulator
- Maker
- Microchip
- Package
- SOT-23-5
- Pins
- 5
- Details
- VR-IC: LDO, CE, -Error, 2.5V±3%, 150mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
3 more parts have no package on record
RT1P141TMitNot recordedNot recordedNot recordedMit
- What it is
- Not recorded
- Maker
- Mit
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Si-pnp-Digi: Sw, 50V, 100mA, 125mW, 200MHz, R1/R2=10k/10k
- Source
- Published code list
Is it dead? The meter test is below: This part.
SP6641A5 pins, MaxLinear (Sipex)Not recordedNot recorded5 pinsMaxLinear (Sipex)
- What it is
- Not recorded
- Maker
- MaxLinear (Sipex)
- Package
- Not recorded
- Pins
- 5
- Details
- 500mA Alkaline DC/DC Boost Regulator
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
XC6GN4102HRTorexNot recordedNot recordedNot recordedTorex
- What it is
- Not recorded
- Maker
- Torex
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS-IC: Voltage Detector 4,1V, Reset Open drain output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
RF amplifier
Voltage, board powered, on the output pin that the bias resistor or choke feeds.
Working, it reads
The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
Dead, it reads
- Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
- Output pin at the full supply voltage: open inside, no current flowing.
- On the board:
- Measured on the board with power on; the bias network is part of the reading.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The figures depend on the part and its bias resistor. The datasheet gives both.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.