SMD code PR-
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
97 parts are printed PR-
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
SMF40CASOD-123FTVS diode, 2 pins, HXYTVS diodeSOD-123F2 pinsHXY
- What it is
- TVS diode
- Maker
- HXY
- Package
- SOD-123F
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
1SMB170ASMBTVS diode, 2 pins, onsemiTVS diodeSMB2 pinsonsemi
- What it is
- TVS diode
- Maker
- onsemi
- Package
- SMB
- Pins
- 2
- Details
- TVS: 170V, 2.2A, 500W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
1SMB170AT3SMBTVS diode, 2 pins, onsemiTVS diodeSMB2 pinsonsemi
- What it is
- TVS diode
- Maker
- onsemi
- Package
- SMB
- Pins
- 2
- Details
- 170V Unidirectional TVS Diode
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
2SA1712-RSOT-23PNP transistor, 3 pins, ToshibaPNP transistorSOT-233 pinsToshiba
- What it is
- PNP transistor
- Maker
- Toshiba
- Package
- SOT-23
- Pins
- 3
- Details
- Si-pnp: Sw, 29V, 30mA, 200mW, B=100..200, 15/110ns
- Source
- Published code list
Is it dead? The meter test is below: PNP transistor.
2SD814-RSOT-233 pins, PanNot recordedSOT-233 pinsPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- SOT-23
- Pins
- 3
- Details
- Si-npn: AF, LN, 150V, 50mA, 200mW, B=130..220, 150MHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
2SD1511-RSOT-893 pins, PanNot recordedSOT-893 pinsPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- SOT-89
- Pins
- 3
- Details
- Si-npn-Darl: AF, 100V, 1A, 1W, 150MHz, B=8k.. 20k
- Source
- Published code list
Is it dead? The meter test is below: This part.
2SD1821-RSOT-3233 pins, PanNot recordedSOT-3233 pinsPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- SOT-323
- Pins
- 3
- Details
- Si-npn: AF, LN, 150V, 100mA, 150mW, B=130..220, 150MHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
2SD2240-RSOT-4163 pins, PanNot recordedSOT-4163 pinsPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- SOT-416
- Pins
- 3
- Details
- Si-npn: AF, LN, 150V, 100mA, 125mW, B=130..200, 150MHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
2SJ356SOT-893 pins, NEC ElectronicsNot recordedSOT-893 pinsNEC Electronics
- What it is
- Not recorded
- Maker
- NEC Electronics
- Package
- SOT-89
- Pins
- 3
- Details
- p-MOS*-e: V-MOS, LogL, 60V, ±2A, <0,5Ω(5A)
- Source
- Published code list
Is it dead? The meter test is below: This part.
3.0SMB200ASMBZener diode, 2 pins, Ruilong Yuan ElectronicsZener diodeSMB2 pinsRuilong Yuan Electronics
- What it is
- Zener diode
- Maker
- Ruilong Yuan Electronics
- Package
- SMB
- Pins
- 2
- Details
- Zener diode: 189.0..209.0V, Zzt=875, Izt=3.7mA, 3W
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
6.0SMAJ170ASMATVS diode, 2 pins, UN SemiconductorTVS diodeSMA2 pinsUN Semiconductor
- What it is
- TVS diode
- Maker
- UN Semiconductor
- Package
- SMA
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=170.0V, Vbr=189.0..209.0V, Ipp=2.2A, 600W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
4 more parts have no package on record
2SA2199-RPNP transistor, ROHMPNP transistorNot recordedNot recordedROHM
- What it is
- PNP transistor
- Maker
- ROHM
- Package
- Not recorded
- Pins
- Not recorded
- Details
- PNP transistor: AF, 50V, 100mA, 150mW, B=180..390, 110MHz
- Source
- Published code list
Is it dead? The meter test is below: PNP transistor.
2SA2199R3 pins, ROHMNot recordedNot recorded3 pinsROHM
- What it is
- Not recorded
- Maker
- ROHM
- Package
- Not recorded
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: This part.
74AUP1G06GFNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Inverter (ODO)
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AUP1G06GMNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Inverter (ODO)
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PNP transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.