Skip to content

SMD code Q4 in SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

5 parts in SOT-23 are printed Q4

Not sure which one you have?

Answer up to 4 quick questions and these 11 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 2SC1321-4SOT-23RF transistor, NEC ElectronicsRF transistorNEC Electronics
    What it is
    RF transistor
    Maker
    NEC Electronics
    Package
    SOT-23
    Pins
    3
    Details
    NPN transistor: UHF, 30V, 10mA, 100mW, B=90..180, 900MHz
    Source
    Published code list

    Is it dead? The meter test is below: Bipolar transistor.

  • APX809S00-23SA-7SOT-23Voltage supervisor, Diodes IncorporatedVoltage supervisorDiodes Incorporated
    What it is
    Voltage supervisor
    Maker
    Diodes Incorporated
    Package
    SOT-23
    Pins
    3
    Details
    Voltage detector IC: 2.25V±1.5%, -Reset PPO, Rdt=1.7ms
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • ELM7644HBBSOT-23Voltage supervisor, ELM TechnologyVoltage supervisorELM Technology
    What it is
    Voltage supervisor
    Maker
    ELM Technology
    Package
    SOT-23
    Pins
    3
    Details
    Voltage detector IC: 4.4V±2%, +Reset PPO, Rdt=500ms
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • R3130N30AA8SOT-23Nisshinbo Micro DevicesNot recordedNisshinbo Micro Devices
    What it is
    Not recorded
    Maker
    Nisshinbo Micro Devices
    Package
    SOT-23
    Pins
    3
    Details
    CMOS-IC: Voltage Detector 3V, -Reset Push-pull output, 50ms
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • SP809EK-2-9SOT-23Voltage supervisor, SipexVoltage supervisorSipex
    What it is
    Voltage supervisor
    Maker
    Sipex
    Package
    SOT-23
    Pins
    3
    Details
    Voltage detector IC: 2.9V±1.5%, -Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • 6 more parts have no package on record. Nothing rules them out, so they stay.
    • 2SC2813-4RF transistor, Sanyo ElectricRF transistorSanyo Electric
      What it is
      RF transistor
      Maker
      Sanyo Electric
      Package
      Not recorded
      Pins
      Not recorded
      Details
      NPN transistor: RF, GP, 25V, 30mA, 150mW, B=90..180, 600MHz
      Source
      Published code list

      Is it dead? The meter test is below: Bipolar transistor.

    • 74AUP1G04FW5Diodes IncorporatedNot recordedDiodes Incorporated
      What it is
      Not recorded
      Maker
      Diodes Incorporated
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS logic IC: Single inverter
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • BAT54-09P6FILMSchottky diode, STMicroelectronicsSchottky diodeSTMicroelectronics
      What it is
      Schottky diode
      Maker
      STMicroelectronics
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Published code list

      Is it dead? The meter test is below: Schottky diode.

    • KTC601F-YKECNot recordedKEC
      What it is
      Not recorded
      Maker
      KEC
      Package
      Not recorded
      Pins
      Not recorded
      Details
      NPN transistor: Dual GP, 50V, 150mA, 100mW, B=120..240, 80MHz
      Source
      Published code list

      Is it dead? The meter test is below: Bipolar transistor.

    • MMBC1321Q4onsemiNot recordedonsemi
      What it is
      Not recorded
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      npn VHF amp fT 0.6GHz
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • R5210N002CNisshinbo Micro DevicesNot recordedNisshinbo Micro Devices
      What it is
      Not recorded
      Maker
      Nisshinbo Micro Devices
      Package
      Not recorded
      Pins
      Not recorded
      Details
      VR-IC: PWM step-down DC-DC converter, Vr=3.3V, DC/DCout=2.5V, Vdet= 4V
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as Q4

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.