Skip to content

SMD code R20

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

R20 on a chip resistor

0.2 Ω

0.2 Ω resistor

The R stands in for the decimal point, which is how sub-ohm and fractional values are printed. The same marking also reads as 0.2 µH on an inductor or 0.2 pF on a capacitor, and nothing in the code says which; the body of the part does.

Other readings of the same characters, most likely first

  • 0.2 µH inductor
  • 0.2 pF capacitor

Check it with a meter

Lift one end and measure across it. A good one reads 0.2 Ω. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 0.2 Ω on the board is a fault. Open, or well above 0.2 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 0.2 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SOT-23-5, SOT-23, SMB), R20 is a part code instead. Those parts are listed below.

19 parts are printed R20

Not sure which one you have?

Answer up to 4 quick questions and these 19 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • CJ3420SOT-23N-channel MOSFET, 3 pins, JSCJN-channel MOSFETSOT-233 pinsJSCJ
    What it is
    N-channel MOSFET
    Maker
    JSCJ
    Package
    SOT-23
    Pins
    3
    Details
    MOSFET, N-channel, 20 V, 6 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • KIC77C20M2SOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 2.0 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • KIC77C20T2SOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 2.0 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • REF3320AIDCKSOT-323Voltage reference, 3 pins, Texas InstrumentsVoltage referenceSOT-3233 pinsTexas Instruments
    What it is
    Voltage reference
    Maker
    Texas Instruments
    Package
    SOT-323
    Pins
    3
    Details
    3.9μA, SC70-3, SOT-23-3, and UQFN-8, 30ppm/°C Drift Voltage Reference
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • WM02N50MSOT-233 pins, WayonNot recordedSOT-233 pinsWayon
    What it is
    Not recorded
    Maker
    Wayon
    Package
    SOT-23
    Pins
    3
    Details
    MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • AD1582SOT-233 pins, Analog DevicesNot recordedSOT-233 pinsAnalog Devices
    What it is
    Not recorded
    Maker
    Analog Devices
    Package
    SOT-23
    Pins
    3
    Details
    2.50 V Precision Series Mode Voltage References
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • AD1582BRTZ-REEL7SOT-233 pins, Analog DevicesNot recordedSOT-233 pinsAnalog Devices
    What it is
    Not recorded
    Maker
    Analog Devices
    Package
    SOT-23
    Pins
    3
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • CM7R250-20B-TSOT-23LDO regulator, 3 pins, Canaan MicroelectronicsLDO regulatorSOT-233 pinsCanaan Microelectronics
    What it is
    LDO regulator
    Maker
    Canaan Microelectronics
    Package
    SOT-23
    Pins
    3
    Details
    Linear voltage regulator IC: LDO, 2.0V±2%, 150mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • IXD1421AB20ER-GUSP-6CLDO regulator, 6 pins, IXYSLDO regulatorUSP-6C6 pinsIXYS
    What it is
    LDO regulator
    Maker
    IXYS
    Package
    USP-6C
    Pins
    6
    Details
    Linear voltage regulator IC: LDO, Dual out, Vo1/Vo2=2.50V±1%/2.50V±1%, 300mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • R1161N201DSOT-23-55 pins, Nisshinbo Micro DevicesNot recordedSOT-23-55 pinsNisshinbo Micro Devices
    What it is
    Not recorded
    Maker
    Nisshinbo Micro Devices
    Package
    SOT-23-5
    Pins
    5
    Details
    VR-IC: LDO, CE, auto discharge, 2V±2%, 350mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • SPX5205M5-L-2-0SOT-23-55 pins, EXAR CorporationNot recordedSOT-23-55 pinsEXAR Corporation
    What it is
    Not recorded
    Maker
    EXAR Corporation
    Package
    SOT-23-5
    Pins
    5
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • TK11120CSSOT-23-55 pins, TokNot recordedSOT-23-55 pinsTok
    What it is
    Not recorded
    Maker
    Tok
    Package
    SOT-23-5
    Pins
    5
    Details
    VR-IC: LDO, -CE, 2V±1,5%, 200mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • TK11220UMSOT-89-55 pins, TokNot recordedSOT-89-55 pinsTok
    What it is
    Not recorded
    Maker
    Tok
    Package
    SOT-89-5
    Pins
    5
    Details
    VR-IC: LDO, CE, 2V±5%, 170mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • 2 more parts have no package on record
    • SGM836-2.9XTDI6GVoltage supervisor, 6 pins, SG MicroVoltage supervisorNot recorded6 pinsSG Micro
      What it is
      Voltage supervisor
      Maker
      SG Micro
      Package
      Not recorded
      Pins
      6
      Details
      2.7 V threshold, Microprocessor Supervisory Circuit with Programmable Delay Time
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • TK11220CMTokNot recordedNot recordedNot recordedTok
      What it is
      Not recorded
      Maker
      Tok
      Package
      Not recorded
      Pins
      Not recorded
      Details
      VR-IC: LDO, CE, 2V±5%, 150mA
      Source
      Published code list

      Is it dead? The meter test is below: Voltage regulator.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as R20

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.