SMD code S13
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
17 parts are printed S13
Not sure which one you have?
Answer up to 4 quick questions and these 17 parts are ranked, with a meter test that settles it. It works on a dead part too.
S-SM130ASMASchottky diode, 2 pins, LRCSchottky diodeSMA2 pinsLRC
- What it is
- Schottky diode
- Maker
- LRC
- Package
- SMA
- Pins
- 2
- Details
- Schottky diode, VR 30 V, IF 1 A, VF Max 0.55 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
SFM13SMARectifier, 2 pins, Formosa MicrosemiRectifierSMA2 pinsFormosa Microsemi
- What it is
- Rectifier
- Maker
- Formosa Microsemi
- Package
- SMA
- Pins
- 2
- Details
- Rectifier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
SM130ASMASchottky diode, 2 pins, LRCSchottky diodeSMA2 pinsLRC
- What it is
- Schottky diode
- Maker
- LRC
- Package
- SMA
- Pins
- 2
- Details
- Schottky diode, VR 30 V, IF 1 A, VF Max 0.55 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
SM130AFSMAFSchottky diode, 2 pins, LRCSchottky diodeSMAF2 pinsLRC
- What it is
- Schottky diode
- Maker
- LRC
- Package
- SMAF
- Pins
- 2
- Details
- Schottky diode, VR 30 V, IF 1 A, VF Max 0.55 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
SS13WSOD-123Schottky diode, 2 pins, HottechSchottky diodeSOD-1232 pinsHottech
- What it is
- Schottky diode
- Maker
- Hottech
- Package
- SOD-123
- Pins
- 2
- Details
- Schottky diode, 30 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
BBY42SOT-233 pins, Philips Semiconductors / VALVO GmbHNot recordedSOT-233 pinsPhilips Semiconductors / VALVO GmbH
- What it is
- Not recorded
- Maker
- Philips Semiconductors / VALVO GmbH
- Package
- SOT-23
- Pins
- 3
- Details
- equivalent BB909A
- Source
- Published code list
Is it dead? The meter test is below: This part.
FJX3013RSOT-323Digital transistor (NPN, resistors built in), 3 pins, Fairchild SemiconductorDigital transistor (NPN, resistors built in)SOT-3233 pinsFairchild Semiconductor
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- Fairchild Semiconductor
- Package
- SOT-323
- Pins
- 3
- Details
- NPN transistor: Sw, 50V, 100mA, 200mW, R1/R2=2.2k/47k
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
KSY13SOT-1434 pins, InfineonNot recordedSOT-1434 pinsInfineon
- What it is
- Not recorded
- Maker
- Infineon
- Package
- SOT-143
- Pins
- 4
- Details
- equivalent KSY10
- Source
- Published code list
Is it dead? The meter test is below: This part.
RP202N131BSOT-23-5LDO regulator, 5 pins, RicohLDO regulatorSOT-23-55 pinsRicoh
- What it is
- LDO regulator
- Maker
- Ricoh
- Package
- SOT-23-5
- Pins
- 5
- Details
- Linear voltage regulator IC: LDO, 1.3V±1%, 200mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
SGM2122-KYN6GSOT-23-6LDO regulator, 6 pins, SG MicroLDO regulatorSOT-23-66 pinsSG Micro
- What it is
- LDO regulator
- Maker
- SG Micro
- Package
- SOT-23-6
- Pins
- 6
- Details
- Linear voltage regulator IC: LDO, Dual out, Vout1/Vout2=3.0V/1.8V±2%, 250mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
STPS130ESOT-223Schottky diode, SGS-Thomson MicroelectronicsSchottky diodeSOT-223Not recordedSGS-Thomson Microelectronics
- What it is
- Schottky diode
- Maker
- SGS-Thomson Microelectronics
- Package
- SOT-223
- Pins
- Not recorded
- Details
- Diode: SBR, 30V, 1A, Vf<0.55V(1A)
- Source
- Published code list
Is it dead? The meter test is below: Schottky diode.
4 more parts have no package on record
PJS6413MOSFET, PanjitMOSFETNot recordedNot recordedPanjit
- What it is
- MOSFET
- Maker
- Panjit
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
SFM13-LRectifier, Formosa MicrosemiRectifierNot recordedNot recordedFormosa Microsemi
- What it is
- Rectifier
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Rectifier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
SFM13-SFRectifier, Formosa MicrosemiRectifierNot recordedNot recordedFormosa Microsemi
- What it is
- Rectifier
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Rectifier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
SFM13-SF-Q1Rectifier, Formosa MicrosemiRectifierNot recordedNot recordedFormosa Microsemi
- What it is
- Rectifier
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Rectifier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Digital transistor
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
- Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
- From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
- Base to emitter near 0 Ω: failed short.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
- Watch for:
- On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as S13
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with S13
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 107 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.