SMD code S5s
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
The last letter, s, is lower case, which on NXP and Philips parts is a date or factory code, so it was set aside and S5 was searched.
109 parts are printed S5s
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
SMS3924-079LFSOD-523Schottky diode, 2 pins, SkyworksSchottky diodeSOD-5232 pinsSkyworks
- What it is
- Schottky diode
- Maker
- Skyworks
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
SR05LSOT-143ESD protection diode, 4 pins, Galaxy MicroelectronicsESD protection diodeSOT-1434 pinsGalaxy Microelectronics
- What it is
- ESD protection diode
- Maker
- Galaxy Microelectronics
- Package
- SOT-143
- Pins
- 4
- Details
- 5V, 90W, Surface Mount TVS
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
SRV3.3-4DFNESD protection diode, ProTek DevicesESD protection diodeDFNNot recordedProTek Devices
- What it is
- ESD protection diode
- Maker
- ProTek Devices
- Package
- DFN
- Pins
- Not recorded
- Details
- Ultra Low Capacitance Steering Diode/TVS Array
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
SRV05-4SOT-23-6ESD protection diode, 6 pins, ProTek DevicesESD protection diodeSOT-23-66 pinsProTek Devices
- What it is
- ESD protection diode
- Maker
- ProTek Devices
- Package
- SOT-23-6
- Pins
- 6
- Details
- Ultra Low Capacitance Steering Diode/TVS Array
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
SS15SMASchottky diode, 2 pins, Taitron ComponentsSchottky diodeSMA2 pinsTaitron Components
- What it is
- Schottky diode
- Maker
- Taitron Components
- Package
- SMA
- Pins
- 2
- Details
- Surface Mount Schottky Rectifiers
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
SS25SMBSchottky diode, 2 pins, Taitron ComponentsSchottky diodeSMB2 pinsTaitron Components
- What it is
- Schottky diode
- Maker
- Taitron Components
- Package
- SMB
- Pins
- 2
- Details
- Surface Mount Schottky Rectifiers
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
SS35SMCSchottky diode, 2 pins, Taitron ComponentsSchottky diodeSMC2 pinsTaitron Components
- What it is
- Schottky diode
- Maker
- Taitron Components
- Package
- SMC
- Pins
- 2
- Details
- Surface Mount Schottky Rectifiers
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
TBZX584B27SOD-523Zener diode, 2 pins, Galaxy MicroelectronicsZener diodeSOD-5232 pinsGalaxy Microelectronics
- What it is
- Zener diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-523
- Pins
- 2
- Details
- 27V, 150mW, Surface Mount Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
TSD103BWSSOD-323Schottky diode, 2 pins, Galaxy MicroelectronicsSchottky diodeSOD-3232 pinsGalaxy Microelectronics
- What it is
- Schottky diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-323
- Pins
- 2
- Details
- 0.35A, 30V, Surface Mount Small Signal Schottky Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
TSR05LSOT-143ESD protection diode, 4 pins, Galaxy MicroelectronicsESD protection diodeSOT-1434 pinsGalaxy Microelectronics
- What it is
- ESD protection diode
- Maker
- Galaxy Microelectronics
- Package
- SOT-143
- Pins
- 4
- Details
- 5V, 90W, Surface Mount TVS
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
TWG4148AD-125WSOT-23-6Switching diode, 6 pins, Taitron ComponentsSwitching diodeSOT-23-66 pinsTaitron Components
- What it is
- Switching diode
- Maker
- Taitron Components
- Package
- SOT-23-6
- Pins
- 6
- Details
- SMD Switching Diodes Arrays(Multiple Terminals)
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
TWG4148AD-125WSSOT-363Switching diode, 6 pins, Taitron ComponentsSwitching diodeSOT-3636 pinsTaitron Components
- What it is
- Switching diode
- Maker
- Taitron Components
- Package
- SOT-363
- Pins
- 6
- Details
- SMD Switching Diodes Arrays(Multiple Terminals)
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
3 more parts have no package on record
SFM15-MS-Q1Rectifier, Formosa MicrosemiRectifierNot recordedNot recordedFormosa Microsemi
- What it is
- Rectifier
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Rectifier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
SMDA05NLIESD protection diode, LeiditechESD protection diodeNot recordedNot recordedLeiditech
- What it is
- ESD protection diode
- Maker
- Leiditech
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
SS15BSchottky diode, Taitron ComponentsSchottky diodeNot recordedNot recordedTaitron Components
- What it is
- Schottky diode
- Maker
- Taitron Components
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Surface Mount Schottky Rectifiers
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.