SMD code SS
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
63 parts are printed SS
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
B0560WSSOD-323Schottky diode, 2 pins, Galaxy MicroelectronicsSchottky diodeSOD-3232 pinsGalaxy Microelectronics
- What it is
- Schottky diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-323
- Pins
- 2
- Details
- 0.5A, 60V, Surface Mount Small Signal Schottky Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
BSS138SOT-23N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138-HFSOT-23N-channel MOSFET, 3 pins, ComchipN-channel MOSFETSOT-233 pinsComchip
- What it is
- N-channel MOSFET
- Maker
- Comchip
- Package
- SOT-23
- Pins
- 3
- Details
- 50 V, 0.2 A N-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138A-P2-HFSOT-23N-channel MOSFET, 3 pins, ComchipN-channel MOSFETSOT-233 pinsComchip
- What it is
- N-channel MOSFET
- Maker
- Comchip
- Package
- SOT-23
- Pins
- 3
- Details
- 50 V, 0.22 A N-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138DWSOT-363N-channel MOSFET, 6 pins, Yangjie Electronic TechN-channel MOSFETSOT-3636 pinsYangjie Electronic Tech
- What it is
- N-channel MOSFET
- Maker
- Yangjie Electronic Tech
- Package
- SOT-363
- Pins
- 6
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138KSOT-23N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 50 V, 0.2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138LT1GSOT-23N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 50 V, 0.2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138LT3GSOT-23N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 50 V, 0.2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138NH6327SOT-23N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 50 V, 0.2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138P,215SOT-23N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 50 V, 0.2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BSS138WSOT-323N-channel MOSFET, 3 pins, HottechN-channel MOSFETSOT-3233 pinsHottech
- What it is
- N-channel MOSFET
- Maker
- Hottech
- Package
- SOT-323
- Pins
- 3
- Details
- 0.2A, 50V, 0.2W, N Channel, Small Signal MOSFETs
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
BZX84J-B39SOD-323Zener diode, 2 pins, NexperiaZener diodeSOD-3232 pinsNexperia
- What it is
- Zener diode
- Maker
- Nexperia
- Package
- SOD-323
- Pins
- 2
- Pinout
- 1 cathode
- 2 anode
- Details
- 39 V ±2% voltage regulator (Zener) diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
FMOSBSS138DW-Q1-HSOT-363Dual N-channel MOSFET, 6 pins, Formosa MicrosemiDual N-channel MOSFETSOT-3636 pinsFormosa Microsemi
- What it is
- Dual N-channel MOSFET
- Maker
- Formosa Microsemi
- Package
- SOT-363
- Pins
- 6
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET pair.
FMOSBSS138K2-Q1SOT-23MOSFET, 3 pins, Formosa MicrosemiMOSFETSOT-233 pinsFormosa Microsemi
- What it is
- MOSFET
- Maker
- Formosa Microsemi
- Package
- SOT-23
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
1 more part has no package on record
BSS138-F085N-channel MOSFET, onsemiN-channel MOSFETNot recordedNot recordedonsemi
- What it is
- N-channel MOSFET
- Maker
- onsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- N-Channel Logic Level Enhancement Mode Field Effect Transistor
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
N-channel MOSFET pair
Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as SS
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 8 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.