Skip to content

SMD code T16 in SOT-363

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

1 part in SOT-363 is printed T16

Not sure which one you have?

Answer up to 4 quick questions and these 5 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • PJT7816SOT-363MOSFET, PanjitMOSFETPanjit
    What it is
    MOSFET
    Maker
    Panjit
    Package
    SOT-363
    Pins
    6
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • 4 more parts have no package on record. Nothing rules them out, so they stay.
    • MBRXT160Schottky diode, Galaxy MicroelectronicsSchottky diodeGalaxy Microelectronics
      What it is
      Schottky diode
      Maker
      Galaxy Microelectronics
      Package
      Not recorded
      Pins
      Not recorded
      Details
      1A, 60V, Surface Mount Schottky Barrier Rectifiers
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Schottky diode.

    • TMBRXT160Schottky diode, Galaxy MicroelectronicsSchottky diodeGalaxy Microelectronics
      What it is
      Schottky diode
      Maker
      Galaxy Microelectronics
      Package
      Not recorded
      Pins
      Not recorded
      Details
      1A, 60V, Surface Mount Schottky Barrier Rectifiers
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Schottky diode.

    • 2SC5761NEC ElectronicsNot recordedNEC Electronics
      What it is
      Not recorded
      Maker
      NEC Electronics
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Silicon/Germanium NPN transistor: RF, 8V, 35mA, 80mW, 2GHz, B=200..400
      Source
      Published code list

      Is it dead? The meter test is below: Bipolar transistor.

    • NESG2030M04California Eastern LaboratoriesNot recordedCalifornia Eastern Laboratories
      What it is
      Not recorded
      Maker
      California Eastern Laboratories
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Silicon/Germanium NPN transistor: HF, 8V, 35mA, 80mW, 60GHz, B=200..400
      Source
      Published code list

      Is it dead? The meter test is below: Bipolar transistor.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as T16

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with T16

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.