SMD code T4s
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
The last letter, s, is lower case, which on NXP and Philips parts is a date or factory code, so it was set aside and T4 was searched.
165 parts are printed T4s
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
LNTS4409NWT1GSOT-323N-channel MOSFET, 3 pins, LRCN-channel MOSFETSOT-3233 pinsLRC
- What it is
- N-channel MOSFET
- Maker
- LRC
- Package
- SOT-323
- Pins
- 3
- Details
- MOSFET, N-Channel(with ESD), VDSS 25 V, VGS 8 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
MM3Z3V0SSOD-323Zener diode, 2 pins, onsemiZener diodeSOD-3232 pinsonsemi
- What it is
- Zener diode
- Maker
- onsemi
- Package
- SOD-323
- Pins
- 2
- Details
- 3V, 400mW, Surface Mount Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
MMBD6100SOT-23Switching diode, 3 pins, Taitron ComponentsSwitching diodeSOT-233 pinsTaitron Components
- What it is
- Switching diode
- Maker
- Taitron Components
- Package
- SOT-23
- Pins
- 3
- Details
- 0.2A, 70V, Surface Mount Small Signal Switching Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
MMBD6100WSOT-323Switching diode, 3 pins, PanjitSwitching diodeSOT-3233 pinsPanjit
- What it is
- Switching diode
- Maker
- Panjit
- Package
- SOT-323
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
MMSD4148T1GSOD-123Switching diode, 2 pins, HXYSwitching diodeSOD-1232 pinsHXY
- What it is
- Switching diode
- Maker
- HXY
- Package
- SOD-123
- Pins
- 2
- Details
- Switching diode, 100 V, 0.3 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
MMSZ3V3SOD-123Zener diode, 2 pins, onsemiZener diodeSOD-1232 pinsonsemi
- What it is
- Zener diode
- Maker
- onsemi
- Package
- SOD-123
- Pins
- 2
- Details
- Zener Voltage Regulators MMSZxxxT1G Series, SZMMSZxxxT1G Series
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
P1N4148WSSOD-323Rectifier, 2 pins, PrisemiRectifierSOD-3232 pinsPrisemi
- What it is
- Rectifier
- Maker
- Prisemi
- Package
- SOD-323
- Pins
- 2
- Details
- Rectifier diode, 0.3 A, 75 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
P1N4148WTSOD-523Rectifier, 2 pins, PrisemiRectifierSOD-5232 pinsPrisemi
- What it is
- Rectifier
- Maker
- Prisemi
- Package
- SOD-523
- Pins
- 2
- Details
- Rectifier diode, 0.15 A, 75 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
S-L1N4148WT1GSOD-123Switching diode, 2 pins, LRCSwitching diodeSOD-1232 pinsLRC
- What it is
- Switching diode
- Maker
- LRC
- Package
- SOD-123
- Pins
- 2
- Details
- Switching diode, VR 100 V, IF 200 mA, VF Max 1.25 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
S-LNTK2575LT1GSOT-23N-channel MOSFET, 3 pins, LRCN-channel MOSFETSOT-233 pinsLRC
- What it is
- N-channel MOSFET
- Maker
- LRC
- Package
- SOT-23
- Pins
- 3
- Details
- MOSFET, N-Channel(with ESD), VDSS 25 V, VGS 8 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
S-LNTS4409NWT1GSOT-323N-channel MOSFET, 3 pins, LRCN-channel MOSFETSOT-3233 pinsLRC
- What it is
- N-channel MOSFET
- Maker
- LRC
- Package
- SOT-323
- Pins
- 3
- Details
- MOSFET, N-Channel(with ESD), VDSS 25 V, VGS 8 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
4 more parts have no package on record
NC7WB3125L8Analog switch, onsemiAnalog switchNot recordedNot recordedonsemi
- What it is
- Analog switch
- Maker
- onsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 2-Bit Low Power Bus Switch
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
NTB0104GU12Logic level translator, 12 pins, NXPLogic level translatorNot recorded12 pinsNXP
- What it is
- Logic level translator
- Maker
- NXP
- Package
- Not recorded
- Pins
- 12
- Details
- 1 General description
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
PJSD12ESD protection diode, PanjitESD protection diodeNot recordedNot recordedPanjit
- What it is
- ESD protection diode
- Maker
- Panjit
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
SCS4148DF-CSwitching diode, SeCoSSwitching diodeNot recordedNot recordedSeCoS
- What it is
- Switching diode
- Maker
- SeCoS
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.