SMD code V26
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
29 parts are printed V26
Not sure which one you have?
Answer up to 4 quick questions and these 29 parts are ranked, with a meter test that settles it. It works on a dead part too.
DZ23C30SOT-23Zener diode, 3 pins, PanjitZener diodeSOT-233 pinsPanjit
- What it is
- Zener diode
- Maker
- Panjit
- Package
- SOT-23
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
KIC73A26M2SOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
- What it is
- Voltage supervisor
- Maker
- KEC
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS system reset IC with delay time, 2.6 V detection
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
KIC73A26T2SOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
- What it is
- Voltage supervisor
- Maker
- KEC
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS system reset IC with delay time, 2.6 V detection
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
NC7SV126P5SOT-23-5Logic gate, 5 pins, onsemiLogic gateSOT-23-55 pinsonsemi
- What it is
- Logic gate
- Maker
- onsemi
- Package
- SOT-23-5
- Pins
- 5
- Details
- TinyLogic ULP-A Buffer with Three-State Output
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
TGVS26FLSOD-123FSchottky diode, 2 pins, Galaxy MicroelectronicsSchottky diodeSOD-123F2 pinsGalaxy Microelectronics
- What it is
- Schottky diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-123F
- Pins
- 2
- Details
- 2A, 60V, Surface Mount Schottky Barrier Rectifiers
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
74LVC2G126DCMSOP-8Logic gate, 8 pins, NXPLogic gateMSOP-88 pinsNXP
- What it is
- Logic gate
- Maker
- NXP
- Package
- MSOP-8
- Pins
- 8
- Details
- Dual Bus Buffer/Line Driver; 3-State
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74LVC2G126GDDFNLogic gate, NXPLogic gateDFNNot recordedNXP
- What it is
- Logic gate
- Maker
- NXP
- Package
- DFN
- Pins
- Not recorded
- Details
- Dual Bus Buffer/Line Driver; 3-State
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74LVC2G126GMQFNLogic gate, NXPLogic gateQFNNot recordedNXP
- What it is
- Logic gate
- Maker
- NXP
- Package
- QFN
- Pins
- Not recorded
- Details
- Dual Bus Buffer/Line Driver; 3-State
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74LVC2G126GTDFNLogic gate, NXPLogic gateDFNNot recordedNXP
- What it is
- Logic gate
- Maker
- NXP
- Package
- DFN
- Pins
- Not recorded
- Details
- Dual Bus Buffer/Line Driver 3-State
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
BFG67/XRSOT-1434 pins, NXPNot recordedSOT-1434 pinsNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- SOT-143
- Pins
- 4
- Details
- Si-npn: VHF/UHF-A, 20V, 50mA, 200mW, B=65..150, 7,5GHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
DZ23-C30SOT-233 pins, Diodes IncorporatedNot recordedSOT-233 pinsDiodes Incorporated
- What it is
- Not recorded
- Maker
- Diodes Incorporated
- Package
- SOT-23
- Pins
- 3
- Details
- Z-diode: Dual, 30V±5%, 300mW
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
DZ23C30-VSOT-23Zener diode, 3 pins, VishayZener diodeSOT-233 pinsVishay
- What it is
- Zener diode
- Maker
- Vishay
- Package
- SOT-23
- Pins
- 3
- Details
- 2.7V Dual Zener Diodes
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
3 more parts have no package on record
74LVC1G126GVNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Bus buffer gate with 3-state output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74LVC2G126DPLogic gate, NXPLogic gateNot recordedNot recordedNXP
- What it is
- Logic gate
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Dual Bus Buffer/Line Driver; 3-State
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
DZ23B30-VZener diode, VishayZener diodeNot recordedNot recordedVishay
- What it is
- Zener diode
- Maker
- Vishay
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 30V Dual Zener Diodes
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as V26
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with V26
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 2 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.