Skip to content

SMD code WJ in SOD-123

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 38 parts are ranked, with a meter test that settles it. It works on a dead part too.

8 parts have no package on record. Nothing rules them out, so they stay.

  • TCM2-63WX+RF transformer, Mini-CircuitsRF transformerMini-Circuits
    What it is
    RF transformer
    Maker
    Mini-Circuits
    Package
    Not recorded
    Pins
    Not recorded
    Details
    RF transformer, 30-6000 MHz
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: This part.

  • 2SC5784NPN transistor, ToshibaNPN transistorToshiba
    What it is
    NPN transistor
    Maker
    Toshiba
    Package
    Not recorded
    Pins
    Not recorded
    Details
    NPN transistor: Sw, Hi-sp, 40V, 1.5A, 750mW, B=400..1000
    Source
    Published code list

    Is it dead? The meter test is below: NPN transistor.

  • AX5505R26DC-DC converterDC-DC converterNot recorded
    What it is
    DC-DC converter
    Maker
    Not recorded
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Micropower VFM Synchronous Step-up DC/DC Converter
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • BCR135L3Digital transistor (NPN, resistors built in), InfineonDigital transistor (NPN, resistors built in)Infineon
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    Infineon
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Si-npn-Digi: Sw, 50V, 100mA, 250mW, R1/R2=10k/47k, 150MHz
    Source
    Published code list

    Is it dead? The meter test is below: Digital transistor.

  • BD46321GVoltage supervisor, ROHMVoltage supervisorROHM
    What it is
    Voltage supervisor
    Maker
    ROHM
    Package
    Not recorded
    Pins
    Not recorded
    Details
    CMOS-IC: Voltage Detector 3,2V, -Reset Push-pull output, 100ms
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • HD74LV1GW16ACMRenesasNot recordedRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    Not recorded
    Pins
    Not recorded
    Details
    CMOS logic IC: Dual noniverting buffers
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • HD74LV1GW16ACMERenesasNot recordedRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    Not recorded
    Pins
    Not recorded
    Details
    CMOS-Logic: Dual buffer
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • RP300K42DBVoltage supervisor, RicohVoltage supervisorRicoh
    What it is
    Voltage supervisor
    Maker
    Ricoh
    Package
    Not recorded
    Pins
    Not recorded
    Details
    Voltage detector IC: 4.2V±1%, -Reset ODO, -MR, Rdt=200ms
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

NPN transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Red probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.