SMD code Y3 in SOD-523
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
13 parts in SOD-523 are printed Y3
Not sure which one you have?
Answer up to 4 quick questions and these 37 parts are ranked, with a meter test that settles it. It works on a dead part too.
ACZRH584C13-HFSOD-523Zener diode, 2 pins, ComchipZener diode2 pinsComchip
- What it is
- Zener diode
- Maker
- Comchip
- Package
- SOD-523
- Pins
- 2
- Details
- 13 V 0.2 mW zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX584B33SOD-523Zener diode, 2 pins, RectronZener diode2 pinsRectron
- What it is
- Zener diode
- Maker
- Rectron
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX584C13SOD-523Zener diode, 2 pins, Galaxy MicroelectronicsZener diode2 pinsGalaxy Microelectronics
- What it is
- Zener diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX584C13-MSSOD-523Zener diode, 2 pins, MSKSEMIZener diode2 pinsMSKSEMI
- What it is
- Zener diode
- Maker
- MSKSEMI
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX584C13AUSOD-523Zener diode, 2 pins, JieJieZener diode2 pinsJieJie
- What it is
- Zener diode
- Maker
- JieJie
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
CZRH584C13-HFSOD-523Zener diode, 2 pins, ComchipZener diode2 pinsComchip
- What it is
- Zener diode
- Maker
- Comchip
- Package
- SOD-523
- Pins
- 2
- Details
- 13 V 0.2 mW zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
MM5Z13V-CSOD-523Zener diode, 2 pins, SeCoSZener diode2 pinsSeCoS
- What it is
- Zener diode
- Maker
- SeCoS
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
SMV1270-079LFSOD-523Varicap diode, 2 pins, SkyworksVaricap diode2 pinsSkyworks
- What it is
- Varicap diode
- Maker
- Skyworks
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: PIN diode or varicap.
TBZX584C13SOD-523Zener diode, 2 pins, Galaxy MicroelectronicsZener diode2 pinsGalaxy Microelectronics
- What it is
- Zener diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-523
- Pins
- 2
- Details
- 13V, 150mW, Surface Mount Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BAP70-02SOD-523PIN diode, 2 pins, NXPPIN diode2 pinsNXP
- What it is
- PIN diode
- Maker
- NXP
- Package
- SOD-523
- Pins
- 2
- Details
- 1 Product profile 2 Pinning information 3 Ordering information
- Source
- An older or alternative marking, from a published code list
Is it dead? The meter test is below: PIN diode or varicap.
BZT52-C13TSOD-5232 pins, Micro Commercial ComponentsNot recorded2 pinsMicro Commercial Components
- What it is
- Not recorded
- Maker
- Micro Commercial Components
- Package
- SOD-523
- Pins
- 2
- Details
- Z-diode: 13V±5%, Izt=5mA, Zzt=30Ω, 100mW
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
BZT52C13TSOD-523Zener diode, 2 pins, Micro Commercial ComponentsZener diode2 pinsMicro Commercial Components
- What it is
- Zener diode
- Maker
- Micro Commercial Components
- Package
- SOD-523
- Pins
- 2
- Details
- Z-diode: 13V±5%, Izt=5mA, Zzt=30Ω, 150mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MM5Z13VSOD-523Zener diode, 2 pins, SecZener diode2 pinsSec
- What it is
- Zener diode
- Maker
- Sec
- Package
- SOD-523
- Pins
- 2
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
2 more parts have no package on record. Nothing rules them out, so they stay.
ZGFM109V1B-MSZener diode, Formosa MicrosemiZener diodeNot recordedFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZGFM109V1B-MS-Q1Zener diode, Formosa MicrosemiZener diodeNot recordedFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PIN diode or varicap
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.6 to 0.9 V anode to cathode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Codes that begin with Y3
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 15 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.