SMD code Z75
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
18 parts are printed Z75
Not sure which one you have?
Answer up to 4 quick questions and these 18 parts are ranked, with a meter test that settles it. It works on a dead part too.
ACZRA4761-HFSMAFZener diode, 2 pins, ComchipZener diodeSMAF2 pinsComchip
- What it is
- Zener diode
- Maker
- Comchip
- Package
- SMAF
- Pins
- 2
- Details
- 75 V 1 mW zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX84B27SOT-23Zener diode, 3 pins, Galaxy MicroelectronicsZener diodeSOT-233 pinsGalaxy Microelectronics
- What it is
- Zener diode
- Maker
- Galaxy Microelectronics
- Package
- SOT-23
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX84B27-HFSOT-23Zener diode, 3 pins, ComchipZener diodeSOT-233 pinsComchip
- What it is
- Zener diode
- Maker
- Comchip
- Package
- SOT-23
- Pins
- 3
- Details
- 27 V 0.35 mW zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
CZRA4761-HFSMAFZener diode, 2 pins, ComchipZener diodeSMAF2 pinsComchip
- What it is
- Zener diode
- Maker
- Comchip
- Package
- SMAF
- Pins
- 2
- Details
- 75 V 1 mW zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
NC7SZ175P6SOT-323Flip-flop, 3 pins, onsemiFlip-flopSOT-3233 pinsonsemi
- What it is
- Flip-flop
- Maker
- onsemi
- Package
- SOT-323
- Pins
- 3
- Details
- TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
S-SODZ75A-SHSOD-123FZener diode, 2 pins, LRCZener diodeSOD-123F2 pinsLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SOD-123F
- Pins
- 2
- Details
- Zener diode, VZ Min 71.25 V, VZ Nom 75 V, VZ Max 78.75 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
S-SZAF75ASMAFZener diode, 2 pins, LRCZener diodeSMAF2 pinsLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SMAF
- Pins
- 2
- Details
- Zener diode, VZ Min 71.25 V, VZ Nom 75 V, VZ Max 78.75 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
SODZ75A-SHSOD-123FZener diode, 2 pins, LRCZener diodeSOD-123F2 pinsLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SOD-123F
- Pins
- 2
- Details
- Zener diode, VZ Min 71.25 V, VZ Nom 75 V, VZ Max 78.75 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
SZAF75ASMAFZener diode, 2 pins, LRCZener diodeSMAF2 pinsLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SMAF
- Pins
- 2
- Details
- Zener diode, VZ Min 71.25 V, VZ Nom 75 V, VZ Max 78.75 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
TBZX84B27SOT-23Zener diode, 3 pins, Galaxy MicroelectronicsZener diodeSOT-233 pinsGalaxy Microelectronics
- What it is
- Zener diode
- Maker
- Galaxy Microelectronics
- Package
- SOT-23
- Pins
- 3
- Details
- 27V, 350mW, Surface Mount Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZS4761ASMAZener diode, 2 pins, Formosa MicrosemiZener diodeSMA2 pinsFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- SMA
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZS4761A-Q1SMAZener diode, 2 pins, Formosa MicrosemiZener diodeSMA2 pinsFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- SMA
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX84-B27SOT-23Zener diode, 3 pins, NXPZener diodeSOT-233 pinsNXP
- What it is
- Zener diode
- Maker
- NXP
- Package
- SOT-23
- Pins
- 3
- Details
- 27 V ±2% voltage regulator (Zener) diode
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
BZX84-B27-VSOT-233 pins, NexperiaNot recordedSOT-233 pinsNexperia
- What it is
- Not recorded
- Maker
- Nexperia
- Package
- SOT-23
- Pins
- 3
- Details
- Z-diode: 27V±2%, Zzt=25Ω(Izt=80mA), 300mW
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
BZX84B27-VSOT-23Zener diode, 3 pins, VishayZener diodeSOT-233 pinsVishay
- What it is
- Zener diode
- Maker
- Vishay
- Package
- SOT-23
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as Z75
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.