SMD code search: identify a part by its marking

Not sure which one you have?

Answer up to 4 quick questions and these 14 parts are ranked, with a meter test that settles it. It works on a dead part too.

The only part printed D4G3D in our tables

VRD4G3DPT

What it is: LDO regulator
Maker: AnaSem
Package: SOT-23-6
Pins: 6
Details: Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.35V±1%, 200mA, +CE
Source: Published code list

Is it dead?

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.

On the board:: An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:: The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:: Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Was it this one?

Printed with a code easy to misread

These parts are printed with a character that is easy to misread as what you typed. The odd one out is marked on each.

LDO regulator, 6 pins. What differs:

IXD1204C33ADRprinted 04C3DUSP-6BIXYSUSP-6BIXYS
Printed 04C3D on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
IXYS
Package
USP-6B
Pins
6
Details
Linear voltage regulator IC: LDO, 3.35V±2%, 150mA, -CE, PUR
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
IXD1204C302DRprinted 04C30USP-6BIXYSUSP-6BIXYS
Printed 04C30 on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
IXYS
Package
USP-6B
Pins
6
Details
Linear voltage regulator IC: LDO, 3.0V±2%, 150mA, -CE, PUR
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
IXD1204G33ADRprinted 04G3DUSP-6BIXYSUSP-6BIXYS
Printed 04G3D on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
IXYS
Package
USP-6B
Pins
6
Details
Linear voltage regulator IC: LDO, 3.35V±2%, 150mA, -CE, PUR
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
IXD1204G302DRprinted 04G30USP-6BIXYSUSP-6BIXYS
Printed 04G30 on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
IXYS
Package
USP-6B
Pins
6
Details
Linear voltage regulator IC: LDO, 3.0V±2%, 150mA, -CE, PUR
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4C3DPTprinted D4C3DSOT-23-6AnaSemSOT-23-6AnaSem
Printed D4C3D on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.35V±1%, 200mA, +CE
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4C30PTprinted D4C30SOT-23-6AnaSemSOT-23-6AnaSem
Printed D4C30 on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.0V±1%, 200mA, +CE
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4G30PTprinted D4G30SOT-23-6AnaSemSOT-23-6AnaSem
Printed D4G30 on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.0V±1%, 200mA, +CE
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD463DPTprinted D463DSOT-23-6AnaSemSOT-23-6AnaSem
Printed D463D on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.35V±1%, 200mA, +CE
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4630PTprinted D4630SOT-23-6AnaSemSOT-23-6AnaSem
Printed D4630 on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.0V±1%, 200mA, +CE
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
XC6204C33ADRprinted 04C3DUSP-6BTorexUSP-6BTorex
Printed 04C3D on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
Torex
Package
USP-6B
Pins
6
Details
VR-IC: LDO, -CE, int. pull-dwn res., 3.35V±2%, 150mA
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
XC6204C302DRprinted 04C30USP-6BTorexUSP-6BTorex
Printed 04C30 on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
Torex
Package
USP-6B
Pins
6
Details
VR-IC: LDO, -CE, int. pull-dwn res., 3V±2%, 150mA
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
XC6204G33ADRprinted 04G3DUSP-6BTorexUSP-6BTorex
Printed 04G3D on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
Torex
Package
USP-6B
Pins
6
Details
Linear voltage regulator IC: LDO, 3.35V±2%, 150mA, -CE, PUR
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
XC6204G302DRprinted 04G30USP-6BTorexUSP-6BTorex
Printed 04G30 on the part. Easy to misread as D4G3D. Check that character with a loupe before you order anything.
What it is
LDO regulator
Maker
Torex
Package
USP-6B
Pins
6
Details
Linear voltage regulator IC: LDO, 3.0V±2%, 150mA, -CE, PUR
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

18 more parts have codes that begin with D4G3D

Codes that begin with D4G3D

For a marking with its end worn or burnt off. Each one shows its full printed code.

LDO regulator, all AnaSem. What differs:

VRD4G3DPTXprinted D4G3DXSOT-23-6SOT-23-6
Printed D4G3DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4C3DPTXprinted D4C3DXSOT-23-6SOT-23-6
Printed D4C3DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4C30PTXprinted D4C30XSOT-23-6SOT-23-6
Printed D4C30X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4G30PTXprinted D4G30XSOT-23-6SOT-23-6
Printed D4G30X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD463DPTXprinted D463DXSOT-23-6SOT-23-6
Printed D463DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
VRD4630PTXprinted D4630XSOT-23-6SOT-23-6
Printed D4630X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
LDO regulator
Maker
AnaSem
Package
SOT-23-6
Pins
6
Details
Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
Source
Published code list
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
12 more parts have no package on record
- VRD4G3DPLXprinted D4G3DXNot recorded
  Printed D4G3DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4G3DPNXprinted D4G3DXNot recorded
  Printed D4G3DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4C3DPLXprinted D4C3DXNot recorded
  Printed D4C3DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4C3DPNXprinted D4C3DXNot recorded
  Printed D4C3DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4C30PLXprinted D4C30XNot recorded
  Printed D4C30X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4C30PNXprinted D4C30XNot recorded
  Printed D4C30X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.25V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4G30PLXprinted D4G30XNot recorded
  Printed D4G30X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4G30PNXprinted D4G30XNot recorded
  Printed D4G30X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.65V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD463DPLXprinted D463DXNot recorded
  Printed D463DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD463DPNXprinted D463DXNot recorded
  Printed D463DX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.35V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4630PLXprinted D4630XNot recorded
  Printed D4630X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
- VRD4630PNXprinted D4630XNot recorded
  Printed D4630X. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  LDO regulator
  Maker
  AnaSem
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Linear voltage regulator IC: LDO, Dual out, Vo1=4.6V±1%, Vo2=3.0V±1%, 200mA, +CE, CL
  Source
  Published code list
  Is it dead?
  Voltage, board powered, black probe on ground. Then ohms with the power off.
  Working, it reads
  Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
  Dead, it reads
  Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  Power off, input to output near 0 Ω: shorted.
  On the board:
  An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
  Compare:
  The same regulator on another rail or another board shows the right voltages and the right resistances.
  Watch for:
  Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Try Tech free for 30 days. You need a card to start. Unless you cancel during the trial, Tech then costs €12.00 a month plus VAT. See the plans

One code, several parts

Marking codes are not unique. In the standard code book, 6H on a SOT-23 is an NPN transistor, a varicap, an N-channel JFET, two digital transistors, a 3.6 V voltage detector: six parts from five makers. So a search on WhatSMD (What SMD) shows the parts we hold under that code and under codes easily misread as it, with only the columns that tell them apart.

6Hon a SOT-23, in the code book

NPN transistor
Varicap
N-channel JFET
Digital transistor ×2
3.6 V voltage detector

When more than one is left

Tap Help me choose. Up to 4 quick answers: whether the part has failed, then what separates the parts left. Those get ranked with the reasoning and a test that settles it. That uses one identification: 2 a month are free without an account, and 3 with a free account.

When you cannot read it

Tap the camera in the field. We read the characters, keep the ones we are unsure of, and search every reading. A photo too soft to read is turned back on your phone first; if it is the only one you can get, you can still send it.

Get the app

The same search on your phone, and a camera with a light, zoom and tap to focus for a marking you cannot read. Sign in with your email address to use the same account.

Coming soon to the App Store

SMD code search: identify a part by its marking

What’s printed on it?

VRD4G3DPT

Is it dead?

Printed with a code easy to misread

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with D4G3D

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Did you find your part?

One code, several parts

When more than one is left

When you cannot read it

Get the app