Skip to content

SMD code 2132

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

2 parts are printed 2132

Not sure which one you have?

Answer up to 4 quick questions and these 2 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • G2132K21UDFN10 pins, Global Mixed-mode TechnologyNot recordedDFN10 pinsGlobal Mixed-mode Technology
    What it is
    Not recorded
    Maker
    Global Mixed-mode Technology
    Package
    DFN
    Pins
    10
    Details
    Photoflash Capacitor Charger for DSC Feature VCC 2.9V to 5.5V Supply Voltage Operating Range. Suitable voltage range for
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Ceramic capacitor.

  • GSFC2307LSOT-23P-channel MOSFET, 3 pins, Good-ArkP-channel MOSFETSOT-233 pinsGood-Ark
    What it is
    P-channel MOSFET
    Maker
    Good-Ark
    Package
    SOT-23
    Pins
    3
    Details
    P-channel MOSFET, 20 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: P-channel MOSFET.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Ceramic capacitor

Ohms range across it, and a capacitance range with it lifted.

Working, it reads

On the ohms range it reads open, or climbs to open as it charges. Lifted, a capacitance range reads close to its value.

Dead, it reads

  • Near 0 Ω, or a few ohms: shorted. The usual failure, often from a crack caused by board flex or heat, and it can come and go.
  • A steady resistance, kilohms rather than open: cracked and leaking.
  • Lifted, far below its value on a capacitance range: cracked open or drifted. Less common than a short, but it happens.
On the board
a shorted capacitor shorts its whole rail, so every capacitor on that rail reads the same short. Lift one end, or feed the rail from a current-limited supply and feel which part warms up.
Compare:
Chip capacitors are mostly unmarked, so the value comes from the schematic or the same position on a working board.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

P-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Codes that begin with 2132

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.