SMD code 6.0C
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
5 parts are printed 6.0C
Not sure which one you have?
Answer up to 4 quick questions and these 5 parts are ranked, with a meter test that settles it. It works on a dead part too.
2 pins. What differs:
SM4F6.0CASOD-123FTVS diode, YFWTVS diodeSOD-123FYFW
- What it is
- TVS diode
- Maker
- YFW
- Package
- SOD-123F
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
P4SMAFJ6.0CSMAFTVS diode, Dongguan You Feng Wei ElectronicsTVS diodeSMAFDongguan You Feng Wei Electronics
- What it is
- TVS diode
- Maker
- Dongguan You Feng Wei Electronics
- Package
- SMAF
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=6V, Vbr=6.67..8.45V, Ipp=35.1A, 400W(1ms), Bidir.
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
P4SMAJ6.0CSMATVS diode, YeashinTVS diodeSMAYeashin
- What it is
- TVS diode
- Maker
- Yeashin
- Package
- SMA
- Pins
- 2
- Details
- TVS: 6V, 35.1A, 400W (1ms), Bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
P4SMFJ6.0CSOD-123FTVS diode, YeashinTVS diodeSOD-123FYeashin
- What it is
- TVS diode
- Maker
- Yeashin
- Package
- SOD-123F
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=6V, Ipp=35.1A, 400W (1ms), Bidir.
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SMBG6.0CSMBGMicrosemi Integrated Products DivisionNot recordedSMBGMicrosemi Integrated Products Division
- What it is
- Not recorded
- Maker
- Microsemi Integrated Products Division
- Package
- SMBG
- Pins
- 2
- Details
- TVS: 6V, 52.6A, 600W(1ms), Bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 6.0C
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 27 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.