Skip to content

SMD code A

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • WS3221C-6WLCSPWillsemiNot recordedWLCSPNot recordedWillsemi
    What it is
    Not recorded
    Maker
    Willsemi
    Package
    WLCSP
    Pins
    Not recorded
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: This part.

  • 1SS400C2SOD-523Switching diode, 2 pins, CYStekSwitching diodeSOD-5232 pinsCYStek
    What it is
    Switching diode
    Maker
    CYStek
    Package
    SOD-523
    Pins
    2
    Details
    V switching diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • 1SS392SOT-23Schottky diode, 3 pins, ToshibaSchottky diodeSOT-233 pinsToshiba
    What it is
    Schottky diode
    Maker
    Toshiba
    Package
    SOT-23
    Pins
    3
    Details
    dual cc schottky 40V 0.1A
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 2SC2532SOT-23Darlington transistor, 3 pins, ToshibaDarlington transistorSOT-233 pinsToshiba
    What it is
    Darlington transistor
    Maker
    Toshiba
    Package
    SOT-23
    Pins
    3
    Details
    Si-npn-Darl: AF-Drv, 40V, 300mA, 150mW, B>5000
    Source
    Published code list

    Is it dead? The meter test is below: Darlington transistor.

  • 3SK147SOT-1434 pins, SonyNot recordedSOT-1434 pinsSony
    What it is
    Not recorded
    Maker
    Sony
    Package
    SOT-143
    Pins
    4
    Details
    MESFET n-type: GaAs Dual gate, UHF, 12V, 55mA, 150mW, 800MHz
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • 3SK301SOT-1434 pins, PanNot recordedSOT-1434 pinsPan
    What it is
    Not recorded
    Maker
    Pan
    Package
    SOT-143
    Pins
    4
    Details
    n-MOS-d: Dual-Gate, VHF, 15V, 30mA, Idss=5..23mA, Up<1,35V
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • AX6901AASOT-323Voltage supervisor, 3 pins, AXElite TechnologyVoltage supervisorSOT-3233 pinsAXElite Technology
    What it is
    Voltage supervisor
    Maker
    AXElite Technology
    Package
    SOT-323
    Pins
    3
    Details
    Voltage detector IC: 4.63V±1.5%, -Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • AX6901JASOT-323Voltage supervisor, 3 pins, AXElite TechnologyVoltage supervisorSOT-3233 pinsAXElite Technology
    What it is
    Voltage supervisor
    Maker
    AXElite Technology
    Package
    SOT-323
    Pins
    3
    Details
    Voltage detector IC: 2.80V±1.5%, -Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • BA597SOD-3232 pins, InfineonNot recordedSOD-3232 pinsInfineon
    What it is
    Not recorded
    Maker
    Infineon
    Package
    SOD-323
    Pins
    2
    Details
    PIN-diode: Attenuator, 50V, 100mA, >10MHz; code printed in yellow
    Source
    Published code list

    Is it dead? The meter test is below: Silicon diode.

  • BAT14-098SOD-1232 pins, InfineonNot recordedSOD-1232 pinsInfineon
    What it is
    Not recorded
    Maker
    Infineon
    Package
    SOD-123
    Pins
    2
    Details
    Si-diode: Schottky, 4V, 90mA, Vf<0.55V, Cd<0,35pF; code printed in white
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

  • 5 more parts have no package on record
    • WNMD2202-4N-channel MOSFET, WillsemiN-channel MOSFETNot recordedNot recordedWillsemi
      What it is
      N-channel MOSFET
      Maker
      Willsemi
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: N-channel MOSFET.

    • 3SK305N-channel MOSFET, PanasonicN-channel MOSFETNot recordedNot recordedPanasonic
      What it is
      N-channel MOSFET
      Maker
      Panasonic
      Package
      Not recorded
      Pins
      Not recorded
      Details
      MOSFET n-type: Dual gate, VHF-amp, 15V, +30mA, 150mW, Idss=5..23mA
      Source
      Published code list

      Is it dead? The meter test is below: N-channel MOSFET.

    • 7WB3125CMXonsemiNot recordedNot recordedNot recordedonsemi
      What it is
      Not recorded
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS logic IC: 2-Bit bus switch
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • ALM-11066 pins, BroadcomNot recordedNot recorded6 pinsBroadcom
      What it is
      Not recorded
      Maker
      Broadcom
      Package
      Not recorded
      Pins
      6
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • BA892Diode, 2 pins, InfineonDiodeNot recorded2 pinsInfineon
      What it is
      Diode
      Maker
      Infineon
      Package
      Not recorded
      Pins
      2
      Source
      An older or alternative marking, from a published code list

      Is it dead? The meter test is below: Silicon diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Darlington transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the collector and about 1.1 to 1.4 V to the emitter, two junctions in series, and open the other way round. Collector to emitter reads open. Built-in resistors can change these readings.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.