SMD code A
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
230 parts are printed A
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
AP2N1K2EN1SOT-723N-channel MOSFET, 3 pins, Advanced Power ElectronicsN-channel MOSFETSOT-7233 pinsAdvanced Power Electronics
- What it is
- N-channel MOSFET
- Maker
- Advanced Power Electronics
- Package
- SOT-723
- Pins
- 3
- Details
- 20 V, 0.2 A N-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
APL3537AWLCSPLoad switch, AnpecLoad switchWLCSPNot recordedAnpec
- What it is
- Load switch
- Maker
- Anpec
- Package
- WLCSP
- Pins
- Not recorded
- Details
- Ultra-Low On-Resistance, Power Load Switch With Soft Start
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Load switch.
BA892-02VSOD-523Diode, 2 pins, InfineonDiodeSOD-5232 pinsInfineon
- What it is
- Diode
- Maker
- Infineon
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BAR50-02VSOD-523PIN diode, 2 pins, InfineonPIN diodeSOD-5232 pinsInfineon
- What it is
- PIN diode
- Maker
- Infineon
- Package
- SOD-523
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: PIN diode or varicap.
BAR50-03WSOD-323PIN diode, 2 pins, InfineonPIN diodeSOD-3232 pinsInfineon
- What it is
- PIN diode
- Maker
- Infineon
- Package
- SOD-323
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: PIN diode or varicap.
BAS521WTSOD-523Switching diode, 2 pins, DiotecSwitching diodeSOD-5232 pinsDiotec
- What it is
- Switching diode
- Maker
- Diotec
- Package
- SOD-523
- Pins
- 2
- Details
- SMD Small Signal Switching Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BGU8309X2SONRF amplifier (MMIC), 5 pins, NXPRF amplifier (MMIC)X2SON5 pinsNXP
- What it is
- RF amplifier (MMIC)
- Maker
- NXP
- Package
- X2SON
- Pins
- 5
- Details
- SiGe:C low-noise amplifier MMIC for GPS, GLONASS, Galileo and COMPASS
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: RF amplifier.
BR1SS355T1GSOD-323Switching diode, 2 pins, LRCSwitching diodeSOD-3232 pinsLRC
- What it is
- Switching diode
- Maker
- LRC
- Package
- SOD-323
- Pins
- 2
- Details
- Switching diode, VR 90 V, IF 100 mA, VF Max 1.2 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
7 more parts have no package on record
APL3233ABattery protection IC, AnpecBattery protection ICNot recordedNot recordedAnpec
- What it is
- Battery protection IC
- Maker
- Anpec
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Li+ Charger Protection IC
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
APW7582ADC-DC converter, AnpecDC-DC converterNot recordedNot recordedAnpec
- What it is
- DC-DC converter
- Maker
- Anpec
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 0.6A, 5V Input, Low IQ Buck Converter
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
BAS516Switching diode, Formosa MicrosemiSwitching diodeNot recordedNot recordedFormosa Microsemi
- What it is
- Switching diode
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BAS521Switching diode, Formosa MicrosemiSwitching diodeNot recordedNot recordedFormosa Microsemi
- What it is
- Switching diode
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BAS521-Q1Switching diode, Formosa MicrosemiSwitching diodeNot recordedNot recordedFormosa Microsemi
- What it is
- Switching diode
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
CDBZC0130R-HFSchottky diode, ComchipSchottky diodeNot recordedNot recordedComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 30 V, 0.1 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
CDBZC0140R-HFSchottky diode, ComchipSchottky diodeNot recordedNot recordedComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 40 V, 0.1 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Load switch
Voltage, board powered, black probe on ground.
Working, it reads
Switched on, the output pin sits at the input voltage. Switched off, it sits near 0 V.
Dead, it reads
- Output at the input voltage while switched off: the pass element has shorted.
- Input present and switched on, no output: failed open, or shut down into a shorted load. Power off and measure output to ground.
- On the board:
- An output near 0 Ω to ground is usually the load. Lift the output pin to see which.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The pinout and whether the enable is active high or low differ between parts. The datasheet gives both.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PIN diode or varicap
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.6 to 0.9 V anode to cathode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
RF amplifier
Voltage, board powered, on the output pin that the bias resistor or choke feeds.
Working, it reads
The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
Dead, it reads
- Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
- Output pin at the full supply voltage: open inside, no current flowing.
- On the board:
- Measured on the board with power on; the bias network is part of the reading.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The figures depend on the part and its bias resistor. The datasheet gives both.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.