SMD marking

BEin SOD-123F

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

7 parts are printed BE

Not sure which one you have?

Answer up to 4 quick questions and these 7 parts are ranked, with a meter test that settles it. It works on a dead part too.

BZT52H-C6V8SOD-123FZener diode, 2 pins, NexperiaZener diode2 pinsNexperia
What it is
Zener diode
Maker
Nexperia
Package
SOD-123F
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52H-C6V8, opens in a new tab
SMF12ASOD-123FESD protection diode, 2 pins, VishayESD protection diode2 pinsVishay
What it is
ESD protection diode
Maker
Vishay
Package
SOD-123F
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor SMF12A, opens in a new tab
5 more parts have no package on record. Nothing rules them out, so they stay.
- AOZ8328DIESD protection diode, Alpha & Omega SemiconductorESD protection diodeNot recordedAlpha & Omega Semiconductor
  What it is
  ESD protection diode
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection for high-speed interfaces
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOZ8328DI, opens in a new tab
- BZX884B27LZener diode, VishayZener diodeNot recordedVishay
  What it is
  Zener diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  27 V Zener diode
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BZX884B27L, opens in a new tab
- MSMP12ATVS diode, VishayTVS diodeNot recordedVishay
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  150 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor MSMP12A, opens in a new tab
- SMBG12ATVS diode, VishayTVS diodeNot recordedVishay
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMBG12A, opens in a new tab
- SMP12ATVS diode, VishayTVS diodeNot recordedVishay
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  400 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMP12A, opens in a new tab

1 more part is printed with a code easy to misread as BE

Printed with a code easy to misread

One character differs, and it is one that is easy to confuse under a lamp. The odd one out is marked on each.

BZD27B20Pprinted 8ESOD-123FZener diode, 2 pins, VishayZener diodeSOD-123F2 pinsVishay
Printed 8E on the part. Easy to misread as BE. Check that character with a loupe before you order anything.
What it is
Zener diode
Maker
Vishay
Package
SOD-123F
Pins
2
Details
20 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZD27B20P, opens in a new tab

25 more parts have codes that begin with BE

Codes that begin with BE

For a marking with its end worn or burnt off. Each one shows its full printed code.

PZ1AL33B-AUprinted BEHSOD-123FZener diode, 2 pins, PanjitZener diode2 pinsPanjit
Printed BEH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123F
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PZ1AL33B-AU, opens in a new tab
24 more parts have no package on record. Nothing rules them out, so they stay.
- 74AHCT1G08DRLprinted BESLogic gate, 5 pins, Texas InstrumentsLogic gate5 pinsTexas Instruments
  Printed BES. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Logic gate
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  5
  Details
  Single 2-Input Positive-AND Gate
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor 74AHCT1G08DRL, opens in a new tab
- CJBE5005printed BE5005Dual N-channel MOSFET, JSCJDual N-channel MOSFETNot recordedJSCJ
  Printed BE5005. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Dual N-channel MOSFET
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  MOSFET, dual N-channel, 20 V, 10 A
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
  Working, it reads
  Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor CJBE5005, opens in a new tab
- ESDBEF5V0B1Qprinted BEF5ESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed BEF5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 5 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDBEF5V0B1Q, opens in a new tab
- ESDBEH5V0B1Sprinted BEH5ESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed BEH5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 5 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDBEH5V0B1S, opens in a new tab
- ESDBEL5V5B1printed BE5ESD protection diode, JSCJESD protection diodeNot recordedJSCJ
  Printed BE5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 5.5 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDBEL5V5B1, opens in a new tab
- PZ1AH33Bprinted BEHZener diode, PanjitZener diodeNot recordedPanjit
  Printed BEH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PZ1AH33B, opens in a new tab
- PZ1AH33B-AUprinted BEHZener diode, PanjitZener diodeNot recordedPanjit
  Printed BEH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PZ1AH33B-AU, opens in a new tab
- PZS5136BASprinted BEHZener diode, PanjitZener diodeNot recordedPanjit
  Printed BEH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PZS5136BAS, opens in a new tab
- PZS5136BAS-AUprinted BEHZener diode, PanjitZener diodeNot recordedPanjit
  Printed BEH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PZS5136BAS-AU, opens in a new tab
- PZS5247BCHprinted BEHZener diode, PanjitZener diodeNot recordedPanjit
  Printed BEH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Panjit
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor PZS5247BCH, opens in a new tab
- SMCG12Aprinted BEETVS diode, VishayTVS diodeNot recordedVishay
  Printed BEE. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  1500 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMCG12A, opens in a new tab
- SMCG14Aprinted BEKTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEK. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  1500 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMCG14A, opens in a new tab
- SMCG15Aprinted BEMTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  1500 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMCG15A, opens in a new tab
- SMCG18Aprinted BETTVS diode, VishayTVS diodeNot recordedVishay
  Printed BET. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  1500 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMCG18A, opens in a new tab
- SMCG20Aprinted BEVTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEV. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  1500 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMCG20A, opens in a new tab
- SMCG22Aprinted BEXTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEX. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  1500 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMCG22A, opens in a new tab
- SMCG24Aprinted BEZTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEZ. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  1500 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SMCG24A, opens in a new tab
- SN74AHCT1G08DRLprinted BESLogic gate, 5 pins, Texas InstrumentsLogic gate5 pinsTexas Instruments
  Printed BES. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Logic gate
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  5
  Details
  Single 2-Input Positive-AND Gate
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SN74AHCT1G08DRL, opens in a new tab
- TA6F18Aprinted BEPTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6F18A, opens in a new tab
- TA6F18CAprinted BEPTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, bidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6F18CA, opens in a new tab
- TA6L18Aprinted BELTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEL. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6L18A, opens in a new tab
- TA6L18CAprinted BELTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEL. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  600 W TVS diode, bidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TA6L18CA, opens in a new tab
- TPSMA6L12Aprinted BEATVS diode, DiotecTVS diodeNot recordedDiotec
  Printed BEA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Diotec
  Package
  Not recorded
  Pins
  Not recorded
  Details
  SMD Transient Voltage Suppressor Diodes
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TPSMA6L12A, opens in a new tab
- TPSMP18Aprinted BEPTVS diode, VishayTVS diodeNot recordedVishay
  Printed BEP. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  TVS diode
  Maker
  Vishay
  Package
  Not recorded
  Pins
  Not recorded
  Details
  400 W TVS diode, unidirectional
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TPSMP18A, opens in a new tab

Open this in the search to correct a character or try another package.

7 parts are printed BE

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Printed with a code easy to misread

Is it dead?

Codes that begin with BE

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?