Skip to content

SMD code K27

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

K27 on a chip resistor

270 Ω

270 Ω resistor

The K is both the decimal point and the multiplier: 270 Ω.

Check it with a meter

Lift one end and measure across it. A good one reads 270 Ω. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 270 Ω on the board is a fault. Open, or well above 270 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 270 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SOT-23-5, SOT-363, SOT-23), K27 is a part code instead. Those parts are listed below.

Not sure which one you have?

Answer up to 4 quick questions and these 28 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 2N7002KDWSOT-363Dual N-channel MOSFET, 6 pins, PanjitDual N-channel MOSFETSOT-3636 pinsPanjit
    What it is
    Dual N-channel MOSFET
    Maker
    Panjit
    Package
    SOT-363
    Pins
    6
    Details
    Dual N-channel MOSFET, 60 V, 0.1 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET pair.

  • 2N7002KDW-AUSOT-363MOSFET, 6 pins, PanjitMOSFETSOT-3636 pinsPanjit
    What it is
    MOSFET
    Maker
    Panjit
    Package
    SOT-363
    Pins
    6
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • AMMDT2227-HFSOT-363Complementary transistor pair (NPN and PNP), 6 pins, ComchipComplementary transistor pair (NPN and PNP)SOT-3636 pinsComchip
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Comchip
    Package
    SOT-363
    Pins
    6
    Details
    -60 V, -0.6 A NPN+PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • KIC73D27MSOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 2.7 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • KIC73D27TSOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 2.7 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • MMDT2227SOT-363Complementary transistor pair (NPN and PNP), 6 pins, Galaxy MicroelectronicsComplementary transistor pair (NPN and PNP)SOT-3636 pinsGalaxy Microelectronics
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Galaxy Microelectronics
    Package
    SOT-363
    Pins
    6
    Details
    40V, 0.6A, General Purpose NPN+PNP Bipolar Transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • MMDT2227-6LSOT-23-6Complementary transistor pair (NPN and PNP), 6 pins, Galaxy MicroelectronicsComplementary transistor pair (NPN and PNP)SOT-23-66 pinsGalaxy Microelectronics
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Galaxy Microelectronics
    Package
    SOT-23-6
    Pins
    6
    Details
    40V, 0.6A, General Purpose NPN Bipolar Transistor 60V, 0.6A, General Purpose PNP Bipolar Transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • MMDT2227-HFSOT-363Complementary transistor pair (NPN and PNP), 6 pins, ComchipComplementary transistor pair (NPN and PNP)SOT-3636 pinsComchip
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Comchip
    Package
    SOT-363
    Pins
    6
    Details
    -60 V, -0.6 A NPN+PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • MMDT2227DWSOT-363Transistor, 6 pins, YFWTransistorSOT-3636 pinsYFW
    What it is
    Transistor
    Maker
    YFW
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • TMMDT2227SOT-363Complementary transistor pair (NPN and PNP), 6 pins, Galaxy MicroelectronicsComplementary transistor pair (NPN and PNP)SOT-3636 pinsGalaxy Microelectronics
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Galaxy Microelectronics
    Package
    SOT-363
    Pins
    6
    Details
    40V, 0.6A, General Purpose NPN+PNP Bipolar Transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • TSX631ILTSOT-23-5Operational amplifier, 5 pins, STMicroelectronicsOperational amplifierSOT-23-55 pinsSTMicroelectronics
    What it is
    Operational amplifier
    Maker
    STMicroelectronics
    Package
    SOT-23-5
    Pins
    5
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • TSX632IQ2TDFNOperational amplifier, STMicroelectronicsOperational amplifierDFNNot recordedSTMicroelectronics
    What it is
    Operational amplifier
    Maker
    STMicroelectronics
    Package
    DFN
    Pins
    Not recorded
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • TSX632ISTMSOP-8Operational amplifier, 8 pins, STMicroelectronicsOperational amplifierMSOP-88 pinsSTMicroelectronics
    What it is
    Operational amplifier
    Maker
    STMicroelectronics
    Package
    MSOP-8
    Pins
    8
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • TSX634IQ4TQFNOperational amplifier, STMicroelectronicsOperational amplifierQFNNot recordedSTMicroelectronics
    What it is
    Operational amplifier
    Maker
    STMicroelectronics
    Package
    QFN
    Pins
    Not recorded
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • HBNP2227N6SOT-23-6Complementary transistor pair (NPN and PNP), 6 pins, CYStekComplementary transistor pair (NPN and PNP)SOT-23-66 pinsCYStek
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    CYStek
    Package
    SOT-23-6
    Pins
    6
    Details
    50/-60 V, 0.6/-0.6 A NPN+PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

N-channel MOSFET pair

Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor pair

Diode range, part lifted. Test each transistor on its own pins, as the datasheet's pinout gives them.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as K27

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with K27

For a marking with its end worn or burnt off. Each code has a page of its own.

Codes not listed here are printed on 7 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.