Skip to content

SMD code K27 in SOT-363

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 8 parts are ranked, with a meter test that settles it. It works on a dead part too.

all SOT-363, 6 pins. What differs:

  • 2N7002KDWSOT-363Dual N-channel MOSFET, PanjitDual N-channel MOSFETPanjit
    What it is
    Dual N-channel MOSFET
    Maker
    Panjit
    Package
    SOT-363
    Pins
    6
    Details
    Dual N-channel MOSFET, 60 V, 0.1 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET pair.

  • 2N7002KDW-AUSOT-363MOSFET, PanjitMOSFETPanjit
    What it is
    MOSFET
    Maker
    Panjit
    Package
    SOT-363
    Pins
    6
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • AMMDT2227-HFSOT-363Complementary transistor pair (NPN and PNP), ComchipComplementary transistor pair (NPN and PNP)Comchip
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Comchip
    Package
    SOT-363
    Pins
    6
    Details
    -60 V, -0.6 A NPN+PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • MMDT2227SOT-363Complementary transistor pair (NPN and PNP), Galaxy MicroelectronicsComplementary transistor pair (NPN and PNP)Galaxy Microelectronics
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Galaxy Microelectronics
    Package
    SOT-363
    Pins
    6
    Details
    40V, 0.6A, General Purpose NPN+PNP Bipolar Transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • MMDT2227-HFSOT-363Complementary transistor pair (NPN and PNP), ComchipComplementary transistor pair (NPN and PNP)Comchip
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Comchip
    Package
    SOT-363
    Pins
    6
    Details
    -60 V, -0.6 A NPN+PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • MMDT2227DWSOT-363Transistor, YFWTransistorYFW
    What it is
    Transistor
    Maker
    YFW
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • TMMDT2227SOT-363Complementary transistor pair (NPN and PNP), Galaxy MicroelectronicsComplementary transistor pair (NPN and PNP)Galaxy Microelectronics
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Galaxy Microelectronics
    Package
    SOT-363
    Pins
    6
    Details
    40V, 0.6A, General Purpose NPN+PNP Bipolar Transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • HBNP2227S6RSOT-363Complementary transistor pair (NPN and PNP), CYStekComplementary transistor pair (NPN and PNP)CYStek
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    CYStek
    Package
    SOT-363
    Pins
    6
    Details
    40/-60 V, 0.6/-0.6 A NPN+PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

N-channel MOSFET pair

Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor pair

Diode range, part lifted. Test each transistor on its own pins, as the datasheet's pinout gives them.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as K27

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with K27

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.