Skip to content

SMD code K46

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

K46 on a chip resistor

460 Ω

460 Ω resistor

The K is both the decimal point and the multiplier: 460 Ω.

Check it with a meter

Lift one end and measure across it. A good one reads 460 Ω. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 460 Ω on the board is a fault. Open, or well above 460 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 460 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SOT-23-5, SOT-363, SOT-23), K46 is a part code instead. Those parts are listed below.

Not sure which one you have?

Answer up to 4 quick questions and these 21 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BAS40-06SOT-23Schottky diode, 3 pins, Diodes IncorporatedSchottky diodeSOT-233 pinsDiodes Incorporated
    What it is
    Schottky diode
    Maker
    Diodes Incorporated
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • BAS40DW-06SOT-363Schottky diode, 6 pins, SeCoSSchottky diodeSOT-3636 pinsSeCoS
    What it is
    Schottky diode
    Maker
    SeCoS
    Package
    SOT-363
    Pins
    6
    Details
    0.2A, 40V, Surface Mount Small Signal Schottky Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • FMBT3946DW-Q1SOT-363Complementary transistor pair (NPN and PNP), 6 pins, Formosa MicrosemiComplementary transistor pair (NPN and PNP)SOT-3636 pinsFormosa Microsemi
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Formosa Microsemi
    Package
    SOT-363
    Pins
    6
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • HMMDT39467FSOT-363Complementary transistor pair (NPN and PNP), 6 pins, HXYComplementary transistor pair (NPN and PNP)SOT-3636 pinsHXY
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    HXY
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor, 40 V, 0.2 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • KIC73D46MSOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 4.6 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • KIC73D46TSOT-23Voltage supervisor, 3 pins, KECVoltage supervisorSOT-233 pinsKEC
    What it is
    Voltage supervisor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    CMOS system reset IC with delay time, 4.6 V detection
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Integrated circuit.

  • MMDT3946SOT-363Transistor, 6 pins, Galaxy MicroelectronicsTransistorSOT-3636 pinsGalaxy Microelectronics
    What it is
    Transistor
    Maker
    Galaxy Microelectronics
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • MMDT3946-7-FSOT-363Complementary transistor pair (NPN and PNP), 6 pins, HXYComplementary transistor pair (NPN and PNP)SOT-3636 pinsHXY
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    HXY
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor, 40 V, 0.2 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • MMDT3946-CSOT-363Transistor, 6 pins, SeCoSTransistorSOT-3636 pinsSeCoS
    What it is
    Transistor
    Maker
    SeCoS
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • MMDT3946FSOT-23-6Transistor, 6 pins, YFWTransistorSOT-23-66 pinsYFW
    What it is
    Transistor
    Maker
    YFW
    Package
    SOT-23-6
    Pins
    6
    Details
    Bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • PMBT3946YPN,115SOT-363Complementary transistor pair (NPN and PNP), 6 pins, HXYComplementary transistor pair (NPN and PNP)SOT-3636 pinsHXY
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    HXY
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor, 40 V, 0.2 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • TMMDT3946SOT-363Complementary transistor pair (NPN and PNP), 6 pins, Galaxy MicroelectronicsComplementary transistor pair (NPN and PNP)SOT-3636 pinsGalaxy Microelectronics
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    Galaxy Microelectronics
    Package
    SOT-363
    Pins
    6
    Details
    40V, 0.2A, General Purpose NPN+PNP Bipolar Transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • WT3946DWSOT-3636 pins, WayonNot recordedSOT-3636 pinsWayon
    What it is
    Not recorded
    Maker
    Wayon
    Package
    SOT-363
    Pins
    6
    Details
    Bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • HBNP3946S6RSOT-363Complementary transistor pair (NPN and PNP), 6 pins, CYStekComplementary transistor pair (NPN and PNP)SOT-3636 pinsCYStek
    What it is
    Complementary transistor pair (NPN and PNP)
    Maker
    CYStek
    Package
    SOT-363
    Pins
    6
    Details
    40/-40 V, 0.2/-0.2 A NPN+PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor pair.

  • BAS40W-06SOT-323Schottky diode, 3 pins, Diodes IncorporatedSchottky diodeSOT-3233 pinsDiodes Incorporated
    What it is
    Schottky diode
    Maker
    Diodes Incorporated
    Package
    SOT-323
    Pins
    3
    Details
    0.2A, 40V, Surface Mount Small Signal Schottky Diodes
    Source
    Published code list

    Is it dead? The meter test is below: Schottky diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor pair

Diode range, part lifted. Test each transistor on its own pins, as the datasheet's pinout gives them.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as K46

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with K46

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.