SMD code P2p in SOT-23
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
The last letter, p, is lower case, which on NXP and Philips parts is a date or factory code, so it was set aside and P2 was searched.
19 parts in SOT-23 are printed P2p
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
all SOT-23, 3 pins. What differs:
BFR92ASOT-23RF transistor, Taitron ComponentsRF transistorTaitron Components
- What it is
- RF transistor
- Maker
- Taitron Components
- Package
- SOT-23
- Pins
- 3
- Details
- SMD Tuner / Broadband Transistors
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Bipolar transistor.
KRA116SSOT-23Digital transistor (PNP, resistors built in), KECDigital transistor (PNP, resistors built in)KEC
- What it is
- Digital transistor (PNP, resistors built in)
- Maker
- KEC
- Package
- SOT-23
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Digital transistor.
MMBZ5267BSOT-23Zener diode, PanjitZener diodePanjit
- What it is
- Zener diode
- Maker
- Panjit
- Package
- SOT-23
- Pins
- 3
- Details
- 75V, 350mW, Surface Mount Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
PESDLC23T5VUSOT-23ESD protection diode, PrisemiESD protection diodePrisemi
- What it is
- ESD protection diode
- Maker
- Prisemi
- Package
- SOT-23
- Pins
- 3
- Details
- ESD protection diode, 5 V working
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
2SK1577-2SOT-23SonyNot recordedSony
- What it is
- Not recorded
- Maker
- Sony
- Package
- SOT-23
- Pins
- 3
- Details
- FET n-type: VHF/UHF, 35V, 100mA, 150mW, Idss=45..65mA, Up<6V
- Source
- Published code list
Is it dead? The meter test is below: MOSFET.
BFR92ALSOT-23onsemiNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- Si-npn: VHF.UHF, 20V, 25mA, 273mW, B>40, 4.5GHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
BFR92ALT1SOT-23RF transistor, MotorolaRF transistorMotorola
- What it is
- RF transistor
- Maker
- Motorola
- Package
- SOT-23
- Pins
- 3
- Details
- NPN transistor: VHF/UHF, 20V, 25mA, 273mW, B>40, 4.5GHz
- Source
- Published code list
Is it dead? The meter test is below: Bipolar transistor.
ELM7622HCBSOT-23Voltage supervisor, ELM TechnologyVoltage supervisorELM Technology
- What it is
- Voltage supervisor
- Maker
- ELM Technology
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.2V±2%, +Reset PPO, Rdt=150ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
ELM9722CBBSOT-23Voltage supervisor, ELM TechnologyVoltage supervisorELM Technology
- What it is
- Voltage supervisor
- Maker
- ELM Technology
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 2.2V±2.5%, +Reset PPO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
HSMS-2852SOT-23BroadcomNot recordedBroadcom
- What it is
- Not recorded
- Maker
- Broadcom
- Package
- SOT-23
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: This part.
HSMSM-2852SOT-23BroadcomNot recordedBroadcom
- What it is
- Not recorded
- Maker
- Broadcom
- Package
- SOT-23
- Pins
- 3
- Details
- dual series HSMS-285B
- Source
- Published code list
Is it dead? The meter test is below: This part.
LDTA143ELT1GSOT-23Digital transistor (PNP, resistors built in), LRCDigital transistor (PNP, resistors built in)LRC
- What it is
- Digital transistor (PNP, resistors built in)
- Maker
- LRC
- Package
- SOT-23
- Pins
- 3
- Details
- PNP transistor: Sw., 50V, 100mA, B>20, R1/R2=4.7k/4.7k
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
NTR1P02T1SOT-23onsemiNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- Power P-Channel MOSFET
- Source
- Published code list
Is it dead? The meter test is below: P-channel MOSFET.
R3130N26HC3SOT-23Nisshinbo Micro DevicesNot recordedNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 2,6V, -Reset Open drain output, 400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
RT1P241CSOT-23MitNot recordedMit
- What it is
- Not recorded
- Maker
- Mit
- Package
- SOT-23
- Pins
- 3
- Details
- Si-pnp-Digi: Sw, 50V, 100mA, 150mW, 200MHz, R1/R2=22k/22k
- Source
- Published code list
Is it dead? The meter test is below: This part.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Bipolar transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Digital transistor
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
- Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
- From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
- Base to emitter near 0 Ω: failed short.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
- Watch for:
- On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
P-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as P2p
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with P2p
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 154 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.