Skip to content

SMD code R

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 2SB1197-RSOT-23PNP transistor, 3 pins, Weitron TechnologyPNP transistorSOT-233 pinsWeitron Technology
    What it is
    PNP transistor
    Maker
    Weitron Technology
    Package
    SOT-23
    Pins
    3
    Details
    -32V, -0.8A, General Purpose PNP Bipolar Transistor
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • 2SC2480SOT-233 pins, PanNot recordedSOT-233 pinsPan
    What it is
    Not recorded
    Maker
    Pan
    Package
    SOT-23
    Pins
    3
    Details
    Si-npn: VHF/UHF, 30V, 50mA, 150mW, B=800..1600, 1,3GHz
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • 2SC3932SOT-3233 pins, PanNot recordedSOT-3233 pinsPan
    What it is
    Not recorded
    Maker
    Pan
    Package
    SOT-323
    Pins
    3
    Details
    Si-npn: HF-Amp, Osc, 30V, 50mA, 150mW, B=800..1600, >800MHz
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • AX6903DASOT-323Voltage supervisor, 3 pins, AXElite TechnologyVoltage supervisorSOT-3233 pinsAXElite Technology
    What it is
    Voltage supervisor
    Maker
    AXElite Technology
    Package
    SOT-323
    Pins
    3
    Details
    Voltage detector IC: 3.08V±1.5%, -Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • BA585SOD-1232 pins, InfineonNot recordedSOD-1232 pinsInfineon
    What it is
    Not recorded
    Maker
    Infineon
    Package
    SOD-123
    Pins
    2
    Details
    pin diode 50mA max
    Source
    Published code list

    Is it dead? The meter test is below: PIN diode or varicap.

  • BA597SOD-1232 pins, InfineonNot recordedSOD-1232 pinsInfineon
    What it is
    Not recorded
    Maker
    Infineon
    Package
    SOD-123
    Pins
    2
    Details
    PIN-diode: Attenuator, 50V, 100mA, >10MHz; code printed in yellow
    Source
    Published code list

    Is it dead? The meter test is below: Silicon diode.

  • BB620SOD-1232 pins, InfineonNot recordedSOD-1232 pinsInfineon
    What it is
    Not recorded
    Maker
    Infineon
    Package
    SOD-123
    Pins
    2
    Details
    C-diode: VHF-TV/VTR-Tuning, HBand, 30V, 20mA, 62..76pF; code printed in red
    Source
    Published code list

    Is it dead? The meter test is below: Silicon diode.

  • BB644SOD-1232 pins, InfineonNot recordedSOD-1232 pinsInfineon
    What it is
    Not recorded
    Maker
    Infineon
    Package
    SOD-123
    Pins
    2
    Source
    An older or alternative marking, from a published code list

    Is it dead? The meter test is below: This part.

  • EL5108IW-T7SOT-23-66 pins, RenesasNot recordedSOT-23-66 pinsRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    SOT-23-6
    Pins
    6
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • EL5127CYMSOP-1010 pins, RenesasNot recordedMSOP-1010 pinsRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    MSOP-10
    Pins
    10
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • ELM7537CCBSOT-343Voltage supervisor, 4 pins, ELM TechnologyVoltage supervisorSOT-3434 pinsELM Technology
    What it is
    Voltage supervisor
    Maker
    ELM Technology
    Package
    SOT-343
    Pins
    4
    Details
    Voltage detector IC: 3.7V±2%, +Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • ELM7537CCCSOT-353Voltage supervisor, 5 pins, ELM TechnologyVoltage supervisorSOT-3535 pinsELM Technology
    What it is
    Voltage supervisor
    Maker
    ELM Technology
    Package
    SOT-353
    Pins
    5
    Details
    Voltage detector IC: 3.7V±2%, +Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • ELM7537CEBSOT-323Voltage supervisor, 3 pins, ELM TechnologyVoltage supervisorSOT-3233 pinsELM Technology
    What it is
    Voltage supervisor
    Maker
    ELM Technology
    Package
    SOT-323
    Pins
    3
    Details
    Voltage detector IC: 3.7V±2%, +Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • 2 more parts have no package on record
    • ATF-541M44 pins, BroadcomNot recordedNot recorded4 pinsBroadcom
      What it is
      Not recorded
      Maker
      Broadcom
      Package
      Not recorded
      Pins
      4
      Details
      Low Noise Enhancement Mode Pseudomorphic HEMT
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • BA895Diode, 2 pins, InfineonDiodeNot recorded2 pinsInfineon
      What it is
      Diode
      Maker
      Infineon
      Package
      Not recorded
      Pins
      2
      Source
      An older or alternative marking, from a published code list

      Is it dead? The meter test is below: Silicon diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

PNP transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

PIN diode or varicap

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.6 to 0.9 V anode to cathode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A varicap that has drifted in capacitance reads normal on a meter. Only a capacitance meter or the tuning itself shows it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.