Skip to content

SMD code A

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • NSBC114EF3SOT-1123Digital transistor (NPN, resistors built in), 3 pins, onsemiDigital transistor (NPN, resistors built in)SOT-11233 pinsonsemi
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    onsemi
    Package
    SOT-1123
    Pins
    3
    Details
    Digital Transistors (BRT) R1 = 10 k  , R2 = 10 k 
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • NSBC123TDP6SOT-963Digital transistor (NPN, resistors built in), 6 pins, onsemiDigital transistor (NPN, resistors built in)SOT-9636 pinsonsemi
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    onsemi
    Package
    SOT-963
    Pins
    6
    Details
    Dual NPN Bias Resistor Transistors R1 = 2.2 k  , R2 =  k 
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • NSBC123TPDP6SOT-963Digital transistor (resistors built in), 6 pins, onsemiDigital transistor (resistors built in)SOT-9636 pinsonsemi
    What it is
    Digital transistor (resistors built in)
    Maker
    onsemi
    Package
    SOT-963
    Pins
    6
    Details
    Complementary Bias Resistor Transistors R1 = 2.2 k  , R2 =  k 
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • NSR02L30NXDSN2Schottky diode, 2 pins, onsemiSchottky diodeDSN22 pinsonsemi
    What it is
    Schottky diode
    Maker
    onsemi
    Package
    DSN2
    Pins
    2
    Details
    Schottky Barrier Diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • PAM08SD2303SOD-323ESD protection diode, 2 pins, ProTek DevicesESD protection diodeSOD-3232 pinsProTek Devices
    What it is
    ESD protection diode
    Maker
    ProTek Devices
    Package
    SOD-323
    Pins
    2
    Details
    High Powered TVS Arrays
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • PS1201-D32DFN0603-2ESD protection diode, 2 pins, PanjitESD protection diodeDFN0603-22 pinsPanjit
    What it is
    ESD protection diode
    Maker
    Panjit
    Package
    DFN0603-2
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • PSBD2XD30V01DFN0603-2Schottky diode, 2 pins, PrisemiSchottky diodeDFN0603-22 pinsPrisemi
    What it is
    Schottky diode
    Maker
    Prisemi
    Package
    DFN0603-2
    Pins
    2
    Details
    Schottky diode, 30 V, 0.1 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • PSBD2XD30V01NDFN0603-2Schottky diode, 2 pins, PrisemiSchottky diodeDFN0603-22 pinsPrisemi
    What it is
    Schottky diode
    Maker
    Prisemi
    Package
    DFN0603-2
    Pins
    2
    Details
    Schottky diode, 30 V, 0.1 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • PSBD2XD40V01DFN0603-2Schottky diode, 2 pins, PrisemiSchottky diodeDFN0603-22 pinsPrisemi
    What it is
    Schottky diode
    Maker
    Prisemi
    Package
    DFN0603-2
    Pins
    2
    Details
    Schottky diode, 40 V, 0.1 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • 6 more parts have no package on record
    • NSPM0051MUESD protection diode, onsemiESD protection diodeNot recordedNot recordedonsemi
      What it is
      ESD protection diode
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: TVS or ESD protection diode.

    • NTND3184NZDual N-channel MOSFET, onsemiDual N-channel MOSFETNot recordedNot recordedonsemi
      What it is
      Dual N-channel MOSFET
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      MOSFET - Small Signal, Dual N-Channel, 0.65mm x 0.90mm x 0.4mm
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: N-channel MOSFET pair.

    • NTNS3193NZN-channel MOSFET, onsemiN-channel MOSFETNot recordedNot recordedonsemi
      What it is
      N-channel MOSFET
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      MOSFET - Single N - Channel, Small Signal, 0.62 x 0.62 x 0.4
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: N-channel MOSFET.

    • NTNS31315NZN-channel MOSFET, onsemiN-channel MOSFETNot recordedNot recordedonsemi
      What it is
      N-channel MOSFET
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Small Signal MOSFET
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: N-channel MOSFET.

    • PAM17DF2L05CESD protection diode, ProTek DevicesESD protection diodeNot recordedNot recordedProTek Devices
      What it is
      ESD protection diode
      Maker
      ProTek Devices
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Low Capacitance TVS Array
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: TVS or ESD protection diode.

    • PRSB6.8CESD protection diode, ProTek DevicesESD protection diodeNot recordedNot recordedProTek Devices
      What it is
      ESD protection diode
      Maker
      ProTek Devices
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Low Capacitance Miniature TVS Array
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: TVS or ESD protection diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

N-channel MOSFET pair

Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.